Showing 10 results for Diesel Engine
A. Mohebbi, S. Jafarmadar, J. Pashae,
Volume 2, Issue 2 (4-2012)
Abstract
Nitrogen oxides (NOx) contribute to a wide range of environmental effects including the formation of acid rain and
destroy ozone layer. In-cylinder high temperature flame and high oxygen concentration are the parameters which affect
the NOx emissions. The EGR system is a very effective way for reducing NOx emission from a diesel engine (via
reduction of these parameters), particularly at the high load of engine operation condition. In this study, the influence
of EGR on diesel engine combustion, NOx/PM emissions, brake specific fuel consumption (BSFC), engine thermal
efficiency, cylinder pressure and heat release rate (HRR) are analyzed and presented. The experiments have been
conducted on a turbocharged DI diesel engine under full load condition at two different injection timings in order to
distinguish and quantify some effects of Hot and Cooled EGR with various rates on the engine parameters.
Experimental results showed that increase of EGR rate has a negative effect on air-fuel ratio. For a premixed
combustion at constant boost pressure, ignition delay is increased leading to retardation of all combustion process, a
low HRR peak and reduce of in-cylinder peak temperature. Using of Hot EGR reduces NOX emissions whereas PM
emissions are increased. The advance of injection timing resulted in the reduction PM while both NOX emissions and
fuel consumption were increased. The use of cooled EGR was more effective compared to the hot EGR. As a result,
the EGR temperature has no significant impact on NOx emissions. With increasing EGR rate, unequal EGR
distribution was increased in inlet port of cylinders while the reducing EGR temperature (cooled EGR) improved its
distribution among the engine cylinders and decreased the EGR cylinder-to-cylinder variations.
M. H. Shojaeefard, M. M. Etghani, M. Tahani, M. Akbari,
Volume 2, Issue 4 (10-2012)
Abstract
In this study the performance and emissions characteristics of a heavy-duty, direct injection, Compression ignition (CI) engine which is specialized in agriculture, have been investigated experimentally. For this aim, the influence of injection timing, load, engine speed on power, brake specific fuel consumption (BSFC), peak pressure (PP), nitrogen oxides (NOx), carbon dioxide (CO2), Carbon monoxide (CO), hydrocarbon (HC) and Soot emissions has been considered. The tests were performed at various injection timings, loads and speeds. It is used artificial neural network (ANN) for predicting and modeling the engine performance and emission. Multi-objective optimization with respect to engine emissions level and engine power was used in order to deter mine the optimum load, speed and injection timing. For this goal, a fast and elitist non-dominated sorting genetic algorithm II (NSGA II) was applied to obtain maximum engine power with minimum total exhaust emissions as a two objective functions.
M. Azadi, M. Baloo, G. H. Farrahi, S. M. Mirsalim,
Volume 3, Issue 1 (3-2013)
Abstract
In the present paper, a complete literatures review of thermal barrier coating applications in diesel engines
is performed to select a proper type and to find coating effects. The coating system has effects on the fuel
consumption, the power and the combustion efficiency, pollution contents and the fatigue lifetime of engine
components. Usually there are several beneficial influences by applying ceramic layers on the combustion
chamber, including the piston, the cylinder head, the cylinder block, intake and exhaust valves by using a
plasma thermal spray method. Several disadvantages such as producing nitrogen oxides also exist when a
coating system is used. In this article, all effects, advantages and disadvantages of thermal barrier coatings
are investigated based on presented articles.
S. Hassanzadeh Saraei, Sh. Khalilarya, S. Jafarmadar,
Volume 6, Issue 2 (6-2016)
Abstract
Modern diesel engines should have higher pollutant emissions standards with better performance and by using split injection strategies which could optimize the air – fuel mixture, this purpose could be achieved. After achieving the successful validation between modeling and experimental results for both single and double injection strategies, for the first time and in this paper, double injection strategies with new nozzle configuration were used in which number of nozzle holes were doubled and located below the previous holes and then double injection strategies were implemented in a case that for each pulse of injections upper or below holes were used, then this study focused on the effects of the new nozzle configuration holes angle in each pulse of injections. This study confirms that split injection could decrease Nox emission, because it has lower maximum in-cylinder temperature than single injection case due to its separate second stage of combustion, also results showed that using new nozzle configuration with two rows of holes could be more effective in decreasing pollutant emissions without any significant effects on engine performance.
E. Safarian, K. Bilen, M. Akif Ceviz , A. Salimias,
Volume 6, Issue 3 (9-2016)
Abstract
The usage of turbochargers in diesel engines has led to the downsizing of the motors as well as usage of the waste gates in turbochargers. Any dimensional reduction in turbochargers and appurtenant leads to an enhancement on the performance of internal combustion engines and in environmental problems in terms of aerodynamic, thermodynamic and mechanical specifications for both engines and turbochargers. For this reason, the efforts need to be focused on the design of turbochargers and their waste gates accurately, in order to maintain its benefits as much as possible. The extent of waste gate opening, from full opened to closed valve, is demonstrated by the limiting compressor boost pressure ratio. Ultimately, an optimum point of limiting compressor boost pressure ratio is obtained then an increase in the values of BMEP and engine power for the same fuel consumption in range of waste gate opening is achieved
Sina Hassanzadeh Saraei, Shahram Khalilarya, Samad Jafarmadar, Saeed Takhtfirouzeh, Hadi Taghavifar,
Volume 8, Issue 4 (12-2018)
Abstract
Pollutant emissions from diesel engines are significantly affected by fuel injection strategies that could reduce NOx and Soot emissions. For the first time and in this study, numerical simulations were performed to consider the influences of changing the injection duration in each pulse of the double injection strategies on in-cylinder parameters and pollutant emissions. Results confirmed that double injection strategies could influence the in-cylinder temperature, which leads to a reduction in NOx and soot emissions. Additionally, it is seen that decreasing the injection duration could increase the in-cylinder peak pressure and temperature. It could also reduce the soot emission owing to the better fuel atomization. Moreover, RATE+0.5CA case, which injection duration for each pulse increases 0.5 CA, was selected to be the optimum case in reduction of pollutant emissions.
Dr Javad Zareei, Prof Mohamad Hasn Aghakhani, Mr Saeed Ahmadipour,
Volume 9, Issue 3 (9-2019)
Abstract
Changing the compression ratio and presence of turbocharger are two important issues, affecting on performance, and exhaust emissions in internal combustion engines. To study the functional properties and exhaust emissions in regards to compression ratio at different speeds, the numerical solution of the governing equations on the fluid flow inside the combustion chamber and the numerical solution of one-dimensional computational fluid dynamics with the GT-Power software carried out. The diesel engine was with a displacement of 6.4 Lit and Turbocharged six-cylinder. In this engine was chosen, the compression ratio between 15: 1 and 19: 1 with intervals of one unit and the range of engine speed was from 800 to 2400 rpm. The results showed that by the presence of a turbocharger and changing the compression ratio from 17: 1 to 19: 1, the braking power and torque increased by about 56.24% compared to the non-turbocharged engine. In addition, was reduced the brake specific fuel consumption due to higher power output. The amount of CO and HC emissions decreases based on the reduction of the compression ratio compared to the based case, and the NOX value increases due to the production of higher heat than turbocharged engines. The overall results showed that the turbocharged engine with a 19: 1 compression ratio has the best performance and pollution characteristics.
Javad Zareei, Saeed Ahmadi,
Volume 10, Issue 3 (9-2020)
Abstract
In internal combustion engines, the turbocharger and alternative fuels are two important factors affecting engine performance and exhaust emission. In this investigation, a one-dimensional computational fluid dynamics with GT-Power software was used to simulate a six-cylinder turbocharged diesel engine and the naturally aspirated diesel engine to study the performance and exhaust emissions with alternative fuels. The base fuel (diesel), methanol, ethanol, the blend of diesel and ethanol, biodiesel and decane was used. The results showed that decane fuel in the turbocharged engine has more brake power and torque (about 3.86%) compared to the base fuel. Also, the results showed that the turbocharger reduces carbon monoxide and hydrocarbon emissions, and biodiesel fuel has the least amount of carbon monoxide and hydrocarbon among other fuels. At the same time, the lowest NO
X emission was obtained by decane fuel. As a final result can be demonstrated that the decane fuel in the turbocharged engine and the biodiesel fuel in the naturally aspirated engine could be a good alternative ratio to diesel fuel in diesel engines.
Dr Javad Zareei, Abbas Rohani,
Volume 11, Issue 2 (6-2021)
Abstract
Diesel engines are the most trusted sources in the transportation industry. They are also widely used in the urban transportation system. Most pollutants are related to these engines. Therefore, it is important to increase the performance and reduce exhaust emissions of these engines. Alternative fuels are key to meeting upcoming targets.
An experimental and numerical study was performed to investigate the effect of diesel fuel and hydrogen addition to diesel fuel from 0 to 30% on performance and exhaust emissions. Also in this research for changing diesel fuel, an indirect injection engine converted to direct injection engine. The simulation study was conducted by Star cd codes and experimental investigation was carried out on a diesel engine (Perkins 1103A-33TG1), three- cylinders, and four-stroke with maximum engine power 72.3hp at 1800 rpm. The results from this study showed that the increase of hydrogen to diesel fuel improves the thermal efficiency, resulting in lower specific fuel consumption. Also, the results showed that adding hydrogen until 30%, the cylinder pressure increase by about 9% and occurred the delay of peak pressure about 8 degrees of a crank angle compared to diesel fuel. The other obtained results in emission with 30%H2+Diesel showed the soot emission reduced 11.3%, HC and CO reduced nearly 36%, but NOx increased by about 8.3% due to high combustion temperature.
Adel Basiri, Ebrahim Amini,
Volume 12, Issue 1 (3-2022)
Abstract
The objective of the present paper is to assess the capability of several classical damage models in prediction of service lifetime of engine components subjected to Thermo-mechanical Fatigue (TMF) loading. The focus of the present study is based on efficient and robust predictive tools which are suitable in industrial development process, thus the classical fatigue damage models are selected to perform such a tsk. In the classical framework, three strain-based models including Manson-Coffin, Smith-Watson-Topper and Ostergren models and one plastic strain energy-based model are examined. Besides, some correction factors are added to the Manson-Coffin, Ostergren and plastic strain energy models regarding the mean stress and temperature effects. The statistical analysis of the models is carried out utilizing the Low-cycle fatigue and Thermo-mechanical Fatigue tests on standard specimens of A356 aluminum alloy. The analysis indicated that modified Ostergren model is the most reliable model in fatigue lifetime description of the A356 alloy among the others. The studied engine component is a passenger-car diesel engine cylinder head made of A356 aluminum alloy. The temperature, stress and strain distribution fields of the component are considered as the given boundary conditions from our previous work as they are not in the scope of the present investigation. The selected damage models based on the best accuracy identified during statistical analysis are introduced into the ABAQUS software. The modified Ostergren model presented the most accurate and realistic results based on empirical observations of fatigue crack area in diesel engine cylinder heads studied in the literature.
