Automotive Science and Engineering

---

In this paper, numerical simulation of FRP composite cylinder tubes progressive crushing processes is conducted using LS-Dyna. Details on the numerical modeling strategy are given and discussed. It is found that triggers introduced in the numerical simulation can effectively model the bevel trigger at the end of the tubular specimens. It is also found that two-layer finite element model based on the TsaiWu failure criteria is effective in representing the crushing failure mode of the tubular composite specimens and energy absorption characteristics. Employing GEvoM software, two meta-models are then obtained for modeling of both the absorbed energy (E) and the peak crushing force (Fmax) with respect to geometrical design variables using input output data obtained from the finite element modeling. Comparison between obtained meta-models and numerical results in both of training and testing sets show good approximation by using obtained polynomial models.

---

Loading conditions and complex geometry have led the cylinder heads to become the most challenging parts of diesel engines. One of the most important durability problems in diesel engines is due to the cracks valves bridge area. The purpose of this study is a thermo-mechanical analysis of cylinder heads of diesel engines using a two-layer viscoelasticity model. The results of the thermo-mechanical analysis indicated that the maximum temperature and stress occurred in the valves bridge. The results of the finite element analysis correspond with the experimental tests, carried out by researchers, and illustrated the cylinder heads cracked in this region. The results of the thermo-mechanical analysis showed that when the engine is running the stress in the region is compressive caused by the thermal loading and combustion pressure. When the engine shut off the compressive stress turned into the tensile stress because of assembly loads. The valves bridge was under the cyclic tensile and compressive stress and then is under low cycle fatigue. After several cycles the fatigue cracks will appear in this region. The lifetime of this part can be determined through finite element analysis instead of experimental tests. Viscous strain was more than the plastic strain which is not negligible.

---

Loading conditions and complex geometry have led the cylinder heads to become the most challenging parts of diesel engines. One of the most important durability problems in diesel engines is due to the cracks valves bridge area. The purpose of this study is a thermo-mechanical analysis of cylinder heads of diesel engines using a two-layer viscoplasticity model. In this article, mechanical properties of A356.0 alloy, obtained by tensile tests at 25 and 200°C. The results of the thermo-mechanical analysis indicated that the maximum temperature and stress occurred in the valves bridge. The results of the finite element analysis of cylinder heads correspond with the simulation results, carried out by researchers.

---

This paper presents finite element analysis (FEA) of a coated and uncoated cylinder heads of a diesel engine to examine the distribution of temperature and stress. A thermal barrier coating system was applied on the combustion chamber of the cylinder heads, consists of two-layer systems: a ceramic top coat (TC), made of yttria stabilized zirconia (YSZ), ZrO2-8%Y2O3 and also a metallic bond coat (BC), made of Ni-Cr-Al-Y. The coating system in this research comprises 300 μm zirconium oxide TC and 150 μm BC. The three-dimensional model of the cylinder heads was simulated in abaqus software and a two-layer viscoplasticity model was utilized to investigate the elastic, plastic and viscous behavior of the cylinder heads. The elastic and plastic properties of BC and TC layers were considered and the effect of thermal barrier coatings on distribution of temperature and stress was investigated. The aim of this study is to compare the distribution of temperature and stress in the coated and uncoated cylinder heads under thermo-mechanical loads. The results of FEA showed that the thermal barrier coating system reduces the temperature about 53°C because of its lower thermal conductivity. As a result, the cylinder head tolerates lower temperature and fatigue life will increase. The results of thermo-mechanical analysis indicated that the stress in the coated cylinder head decreased approximately 24 MPa for the sake of depletion of temperature gradient which can lead to higher fatigue lifetime. Viscous strain was significant and its amount is not negligible.

---

The primary objective of a brake disc is to absorb frictional heat during braking and dissipated it immediately by convection and radiation. However, during hard and repetitive brakings, thermal coning on brake disc generates surface hot spots which are responsible for the undesired accumulation of compressive stresses on the surface of the brake disc. These stresses would lead to disc cracking and finally failure of it. In the current paper, a coupled transient thermo-mechanical FE analysis of a heavy vehicle braking system is carried out in a way that thermal coning of the disc and surface hot spots and bands are recognizable. Braking condition is chosen from a standard for hard braking in trucks. Moreover, five additional braking actions with different severities are investigated to study the effects of braking severity on thermo-mechanical instability of brake discs. Comparison of numerical results of transient temperature during braking and cooling phases with experiment reveal a high accuracy of thermal prediction of this model. Also, the results show that thermal coning of brake disc is varied between 0.05 to 0.7 mm depending on braking severity and tangential location of the disc. Additionally, surface hot spots experience higher temperature gradients in higher decelerations. Finally, results show that circumferential compressive stresses during braking are the major component of thermal stresses and should be taken into account for life estimation analysis.

---

Loading conditions and complex geometry have led the cylinder heads to become the most challenging parts of diesel engines. The aim of this study is to compare the distribution of temperature and stress in the aluminum and magnesium cylinder heads under thermo-mechanical loads. The three-dimensional model of the cylinder heads was simulated in abaqus software and a two-layer viscoplasticity model was utilized to investigate the elastic, plastic and viscous behavior of the cylinder heads. The temperature and stress results of magnesium alloy was compared to aluminum alloy results. The results of finite element analysis (FEA) showed that surface temperature of the magnesium cylinder heads is about 23°C lower than the aluminum cylinder heads. As a result, the fatigue lifetime of the magnesium cylinder heads can be improved in comparison to the aluminum cylinder heads. The thermo-mechanical analysis showed that the magnesium cylinder heads tolerate less tensile and compressive cyclic stress compared to the aluminum cylinder heads. The stress reduction value in the magnesium cylinder heads was about 10 MPa which can lead to higher fatigue lifetimes in comparison to the aluminum cylinder heads.
 

---

Due to the complex geometry and thermos-mechanical loading, cylinder heads are the most challenging parts among all parts engines. They must endure cyclic thermal and mechanical loading throughout their lifetime. Cast aluminum alloys are normally quenched after solution treatment process to improve aging responses. Rapid quenching can lead to high residual stress. Residual stress is one of the main reasons for failure of cylinder heads. The effect of residual stress on the thermal stress and low cycle fatigue life (LCF) of cylinder heads was studied. For this goal, Solidworks software was used to model the cylinder heads. Then the thermo-mechanical analysis was performed to determine the temperature and stress field in ANSYS software.  Finally, the fatigue life analysis that considers residual stress effect was done. The results of finite element analysis (FEA) proved that the effect of residual stress in LCF is significant which is not negligible. Thus, residual stress must be considered in the thermo-mechanical fatigue analysis of the engines cylinder heads. The numerical results showed that the area where the maximum temperature and stress is occurred is where the least LCF is predicted.

 

---

In this paper, the strength of the gear shifting blocker for Peugeot gearbox is investigated. A hardened steel sheet is used inside the plastic part of shifting blocker to strengthen it. According to the feedback from the customer that this part fails in some conditions, some suggestions for its improvement are presented. In this research, two proposed correction designs are presented to increase the strength of the gear shifting locker by changing on the considered steel sheet. Abaqus software has been used to model the gear shifting blocker and analyze the stress of parts by finite element method. In order to validate the analytical results and choose the proper proposed design to strengthen the blocker part, some experimental tests are performed on the tension-compression test device. By comparing the results of the numerical analysis, it can be observed that the first and second modification designs have improved the stresses of blocker plastic part by 18% and 45%, respectively.