---

The present paper is devoted to a new critical state based plasticity model able to predict drained and undrained behaviour of

granular material. It incorporates a bounding surface plasticity model describing in multilaminate framework to capitalize on

advantages of this mathematical framework. Most of the models developed using stress/strain invariants are not capable of

identifying the parameters depending on directional effects such as principal stress rotation and fabric this is mainly because

stress/strain invariants are scalar quantities. The principal features of this model can be postulated as considering both inherent

and induced anisotropy, principal stress rotation. Since the local instability of saturated sand within post-liquefaction is highly

dependent on the residual inherent/induced anisotropy, bedding plane effects and also the stress/strain path the new mode is

competent to be employed in this regard. The constitutive equations of the model are derived within the context of non-linear

elastic behaviour for the whole medium and plastic sliding of interfaces of predefined planes. As follows, the constitutive

equations are described in detail and then the experimental results and sensitive analysis of key material constants are shown

which all imply the power of the model in predicting of soil behaviour under any condition in soil structures.

---

The main task in the design and construction of impermeable liners in landfills is to block the migration of pollutants to the groundwater

systems or to reduce its rate to a reasonable amount. That is why environmental regulations force governments to construct engineered

waste dumps for waste management purposes. These liners are exposed to various types of chemical, biological, and physical processes

and are affected by the leachate which is produced from decomposition of waste materials accompanying methane gas. The leachate

includes a lot of components such as water and different types of salts. For this reason, the geotechnical characteristics of clay liners

which are evaluated in laboratories using distilled water or tap water might be far different from the representative sample of the in-situ

conditions. There are some evidences regarding the effect of these salts on the physical and mechanical properties of clay barriers which

could affect the long-term performance of these liners. Since the main criterion for impermeable bottom liners in landfills is their

hydraulics conductivity, the increase of this parameter could have a considerable environmental impact. This paper embraces the results

of a recent study on the effect of three inorganic salts, NaCl, CaCl2 and MgCl2 on some geotechnical properties of a common used clay

soil in impermeable bottom barrier in Kahrizak landfill, the main waste disposal center of the Tehran Metropolitan. Also the effect of

bentonite content by adding different percentage of this special clay mineral, 10 and 20 percent, on these properties was investigated.

Laboratory tests like liquid limit, compaction, 1D consolidation and free swell tests were performed for this purpose. Results indicated

that all of these salts could have a considerable effect on the geotechnical properties of the mixtures. The main reason of such effects is

the changes which occur in diffuse double layer of clay particles.

---

Three common approaches to determine the axial pile capacity based on static analysis and in-situ tests are presented, compared and evaluated. The Unified Pile Design (UPD), American Petroleum Institute (API) and a SPT based methods were chosen to be validated. The API is a common method to estimate the axial bearing capacity of piles in marine environments, where as the others are currently used by geotechnical engineers. Seventy pile load test records performed in the northern bank of Persian Gulf with SPT profile have been compiled for methods evaluation. In all cases, pile capacities were measured using full scale static compression and/or pull out loading tests. As the loading tests in some cases were in the format of proof test without reaching the plunging or ultimate bearing capacity, for interpretation the results, offset limit load criteria was employed. Three statistical and probability based approaches in the form of a systematic ranking, called Rank Index, RI, were utilized to evaluate the performance of predictive methods. Wasted Capacity Index (WCI) concept was also applied to validate the efficiency of current methods. The evaluations revealed that among these three predictive methods, the UPD is more accurate and cost effective than the others.

---

Municipal Solid Waste (MSW) materials are among the most complicated materials for geotechnical engineering as their composition includes an organic fraction, which suffers loss of mass over time, and a fibrous part, which acts as reinforcement, governing the MSW shear behavior. Because of these characteristics MSW can be described as a viscous material which shows time dependent behavior. Since the decomposition of MSW leads to gas and leachate generation, the changes in the MSW’s mechanical behavior could be linked to gas emission and leachate production from landfills. This paper deals with the characteristics of MSW materials to provide the necessary data for efficient and safe landfill design, construction and operation. The MSW physical characteristics such as composition, water content and organic content at varying ages, field and laboratory measurements of methane generation and leachate production, MSW compressibility behavior and its shear strength are covered. By presenting these data the authors hope to promote a better understanding of the mechanical behavior of MSW and provide useful data for use in landfill management tasks.

---

Due to the existence of fibrous materials such as plastic fragments, the strength anisotropy of Municipal Solid Waste

(MSW) materials is the main source of differences between their mechanical response in direct shear and triaxial apparatus.

As an extension of earlier research on the mechanical behavior of MSW using a large traixail apparatus, results presented in

Shariatmadari et al. [1] and Karimpour-Fard et al. [2], the current study was programmed and executed. MSW samples were

tested using a computer controlled large shear box apparatus with normal stress levels ranging between 20 to 200 kPa. The

effect of fiber content, fiber orientation, aging and shearing rate on the response of MSW were addressed. The results showed

that shear strength of MSW increases with normal stress, although, in spite of the presence of reinforcement elements in MSW

and unlike the results from triaxial tests, no strain hardening could be observed in their mechanical response. An increase in

the shear strength of MSW was observed with increasing the shearing rate. Increasing the shearing rate from 0.8 to 19

mm/min, enhanced the shear strength of samples from 16 to 27% depending on the shear displacement level. Although, the

same trend was investigated in traixial tests, but lower rate-sensitivity in the mechanical response of MSW in direct shear tests

were observed.

Unlike the results of triaxial tests with aging process, mobilized shear strength level of MSW samples tested under direct

shearing decreased comparing fresh samples. It was also observed that altering the fiber content and their orientation could

affect the mechanical response and shear strength of the MSW. Additionally, there is an optimum fiber angle in MSW which

yields the highest level of shearing strength.