---

Plastic shrinkage is one of the most important parameter which must be considered in hot weather concreting. If plastic shrinkage is not prevented, cracking will be significant, especialy if silica fume is used in the mix. In this paper, the effect of silica fume in bleeding and evaporation was investigated in laboratory. The results showed that in restrained shrinkage, beside relative humidity, temperature and wind velocity, sun rediation also is very important factor in evaporation rate. It is found that under solar radition condition, the evaporation was much larger than the estimated value in ACI 305 Nomogram. The rate of evaporaion under solar radiation was about two folds of evaporation rate under shade condition. The results showed that in terms of crack initiation time, crack width and total cracking area, concrete containing silica fume is more severe than concrete with no silica fume. Reduction of water cement ratio in concrete with silica fume makes the concrete more sensitive in cracking. The results of this project also showed that the severity of the cracking is not related only to rate of bleeding but all environmental factors including like sun radiation or shading and also mix compositions have important roles.

---

Self Compacting Concrete (SCC) specimens with limestone (L) and quartz (Q) powders were formulated. The influence of the type

of the powder on the properties of fresh and hardened concrete was evaluated. Dense packing theories were used for mix design

of samples. The equation of Fuller and Thompson for particle size distribution (PSD) of aggregates was modified with considering

fine particles and a proper PSD curve was obtained for SCC. Experimental results showed that this method needs use of less

powder content and results in higher strength/cement ratio compared to traditional mixing methods. No significant difference was

observed between the compressive strengths of specimens containing limestone (L-specimens) and quartz (Q-specimens) powders,

with similar proportions of materials. The residual compressive strength of specimens was examined at 500°C and contradictory

behaviors were observed. One Q-specimen suffered from explosive spalling, while no spalling was occurred for L-specimens. On

the other hand, the residual strength of remained Q-specimens showed considerable increase compared to L-specimens. The results

show the necessity for more detailed investigations considering different effective parameters.

---

Self-desiccation is the major source of autogenous shrinkage and crack formation in low water-binder ratio (w/b) concretes

which can be reduced by internal curing. In this paper performance of high strength self consolidating concrete (HS-SCC) with

w/b of 0.28 and 0.33 including autogenous shrinkage, drying shrinkage, compressive strength, and resistance to freezing-thawing

was investigated. Then, for the purpose of internal curing, 25% of normal weight coarse aggregate volume was replaced with

saturated lightweight aggregate (LWA) of the same size and its effects on the material properties was studied. Two modes of

external curing, moist and sealed, were applied to test specimens after demoulding. Autogenous shrinkage from 30 minutes to 24

hours after mixing was monitored continuously by a laser system. The initial and final setting time were manifested as a change

of the slope of the obtained deformation curves. Shrinkage after initial setting was 860 and 685 microstrain (&mu&epsilon) for 0.28 and 0.33

w/b mixtures, respectively. The saturated LWA reduced these values to 80 and 295 &mu&epsilon, respectively. By LWA Substitution the 28-

day compressive strength of 0.28 w/b mixture was reduced from 108 to 89 and 98 to 87 MPa for moist and sealed cured specimen,

respectively. The corresponding values for 0.33 w/b mixture was 84 to 80 and 82 to 70 MPa. Shrinkage of 0.28 w/b mixture

without LWA after moist and sealed cured specimen dried for 3 weeks was about 400 &mu&epsilon. Shrinkage of moist and sealed cured

specimen containing LWA was reduced 9% and 25%, respectively. On the contrary for 0.33 w/b mixture an increase was noticed.

Freezing-thawing resistance was improved by sealed curing, decreasing w/b and substituting LWA.