---

When geotechnical engineers are faced with cohesive clayey soils, the engineering properties of those soils may need to be

improved to make them suitable for construction. The aim of this paper is to study the effect of using lime, natural pozzolana or

a combination of both on the geotechnical characteristics of two cohesive soils. Lime or natural pozzolana were added to these

soils at ranges of 0-8% and 0-20%, respectively. In addition, combinations of lime-natural pozzolana were added at the same

ranges. Test specimens were subjected to compaction tests and shear tests. Specimens were cured for 1, 7, 28 and 90 days after

which they were tested for shear strength tests. Based on the experimental results, it was concluded that the combination limenatural

pozzolana showed an appreciable improvement of the cohesion and internal friction angle with curing period and

particularly at later ages for both soils.

---

An experimental-analytical investigation was conducted to study the behavior of high-strength RC deep beams a total of sixteen

reinforced concrete deep beams with compressive strength in range of 59 MPaOf'c O65 MPa were tested under two-point top

loading. The shear span-to-effective depth ratio a/d was 1.10 all the specimens were simply supported and reinforced by

vertical, horizontal and orthogonal steel bars in various arrangements. The test specimens were composed of five series based

on their arrangement of shear reinforcing. The general behavior of tested beams was investigated. Observations were made on

mid-span and loading point deflections, cracks form, failure modes and shear strengths. The test results indicated that both

vertical and horizontal web reinforcement are efficient in shear capacity of deep beams, also the orthogonal shear reinforcement

was the most efficient when placed perpendicular to major axis of diagonal crack. Concentrating of shear reinforcement within

middle region of shear span can improve the ultimate shear strength of deep beam. The test results were then compared with the

predicted ultimate strengths using the ACI 318-08 provisions ACI code tended to either unsafe or scattered results. The

performed investigations deduced that the ACI code provisions need to be revised.

---

In this study compressive strength of carbon nanotube (CNT)/cement composite is computed by analytical method. For this purpose representative elementary volume (REV) as an indicator element of composite is chosen and analyzed by elasticity relationships and Von mises' criterion applied to it. It is assumed that carbon nanotubes are distributed uniformly in the cement and there is perfect bonding in the interface of cement and nanotube. At first for simplicity of computations, carbon nanotubes ( CNTs) are assumed to have unidirectional orientation in the cement matrix. In following, the relations are generalized to consider random distribution of nanotubes in cement, and a new factor suggested for random orientation of fibers in the CNT/cement composite. The results of analytical method are compared with experimental results.

---

The torsional capacity of unreinforced masonry brick buildings is generally inadequate to provide a stable seismic behavior. The

torsional strength is believed to be the most important parameter in earthquake resistance of masonry buildings and the shear

stresses induced in the bed joints of such building’s walls is an important key for design purposes. Brick buildings strengthened

with wire-mesh reinforced concrete overlay are used extensively for building rehabilitation in Iran. Their quick and simple

applications as well as good appearance are the main reasons for the widespread use of such strengthening technique. However,

little attention has been paid to torsional strengthening in terms of both experimental and numerical approach. This paper reports

the response and behavior of two single-story brick masonry buildings having a rigid two-way RC floor diaphragm. Both

specimens were tested under monotonic torsional moment.Numerical work was carried out using non-linear finite element

modeling. Good agreement in terms of torque–twist behavior, and crack patterns was achieved. The unique failure modes of the

specimens were modeled correctly as well. The results demonstrate the effectiveness of reinforced concrete overlay in enhancing

the torsional response of strengthened building. Having evaluated the verification of modeling, an unreinforced brick building

with wall-to-wall vulnerable connections was modeled so that the effect of these connections on torsional performance of brick

building could be studied. Then this building was strengthened with reinforced concrete overlay and the effect of strengthening

on torsional performance of brick buildings with vulnerable connections was predicted numerically.

---

Self-desiccation is the major source of autogenous shrinkage and crack formation in low water-binder ratio (w/b) concretes

which can be reduced by internal curing. In this paper performance of high strength self consolidating concrete (HS-SCC) with

w/b of 0.28 and 0.33 including autogenous shrinkage, drying shrinkage, compressive strength, and resistance to freezing-thawing

was investigated. Then, for the purpose of internal curing, 25% of normal weight coarse aggregate volume was replaced with

saturated lightweight aggregate (LWA) of the same size and its effects on the material properties was studied. Two modes of

external curing, moist and sealed, were applied to test specimens after demoulding. Autogenous shrinkage from 30 minutes to 24

hours after mixing was monitored continuously by a laser system. The initial and final setting time were manifested as a change

of the slope of the obtained deformation curves. Shrinkage after initial setting was 860 and 685 microstrain (&mu&epsilon) for 0.28 and 0.33

w/b mixtures, respectively. The saturated LWA reduced these values to 80 and 295 &mu&epsilon, respectively. By LWA Substitution the 28-

day compressive strength of 0.28 w/b mixture was reduced from 108 to 89 and 98 to 87 MPa for moist and sealed cured specimen,

respectively. The corresponding values for 0.33 w/b mixture was 84 to 80 and 82 to 70 MPa. Shrinkage of 0.28 w/b mixture

without LWA after moist and sealed cured specimen dried for 3 weeks was about 400 &mu&epsilon. Shrinkage of moist and sealed cured

specimen containing LWA was reduced 9% and 25%, respectively. On the contrary for 0.33 w/b mixture an increase was noticed.

Freezing-thawing resistance was improved by sealed curing, decreasing w/b and substituting LWA.

---

Geometrical profile (roughness) of joint surfaces influences the behaviour of rock joints under shear loading. With regard to the

dilation, there are two models of direct shear test that may simulate the original loading condition existing in the location from

where the specimens have been sampled. The first model in which the normal load is constant (CNL) and the discontinuity is free

to dilate in shearing, represents typical situations such as movement of a block on a surface slope as a result of its own weight.

The second model in which the dilatancy is prohibited (VNL), simulates the condition of a block confined in a rock mass in an

underground opening. A shear test conducted under restricted normal displacement (dilation) will generally yield considerably

higher shear strength than one conducted under constant normal stress. In this research, both types of tests were conducted on

smooth and rough surfaces of specimens made from rock like material. The results of the VNL and the CNL direct shear tests on

regular teeth-shaped profile discontinuities indicates that at all levels of normal load, the linear Mohr-Coulomb criterion was not

valid for rough surfaces that subscribed to the power law equations. Increasing normal load emphasized the difference between

the results obtained from two methods, although for lower normal loads the results were nearly similar.

---

This study was conducted to determine the effect of vibration on the curing and compressive strength of lightweight air-trapped

soil (ATS). ATS is manufactured by mixing cement with water and sand and injecting bubbles into the mixture. It is light as

compared to regular soil, can reduce the weight on the ground, and has high fluidity. If ATS is used at construction sites with

many vibration sources, such as pile driving, blasting, and construction machinery, the effect of vibration needs to be seriously

considered. If a road is expanded using ATS to reduce traffic congestion, the ATS quality may decrease because of vibration

generated by traffic moving on the road. In particular, because ATS contains many air bubbles and needs time for curing, the

effect of vibration can be greater than expected. Therefore, the effect of vibration on ATS was evaluated during the curing process

by conducting unconfined compression tests on samples prepared with different values of variables including vibration velocity,

starting vibration time, and mixing ratio. Vibration velocities of 0.25 and 0.50 cm/s did not greatly affect the strength. However,

vibration velocities of above 2.50 cm/s significantly affected the decrease in strength, and the starting vibration time also had a

clear effect on specimens cured for less than 2 hours.

---

Worldwide, asbestos fibers utilized in fiber cement boards, have been recognized as harmful materials regarding the public health and environmental pollutions. These concerns motivate the researchers to find the appropriate alternatives to substitute the asbestos material towards the sustainability policies. In this paper, the applicability of asbestos replacement with three types of agricultural waste fibers, including bagasse, wheat and eucalyptus fibers were experimentally investigated. To this end, the flexural behaviour and microstructure of cement composite boards made by addition of 2 % and 4 % of waste agricultural fibers in combination with and without 5 % replacement of silica fume by mass of cement were evaluated. The results of this study attested the applicability of utilized waste agricultural fibers in production of cement composite boards by improving the flexural and energy absorption characteristics, more or less, depending on the type of fibers. Moreover, it is found that application of silica fume in production of cement composite boards led to an increase in flexural strength.

---

An approach was formulated for the nonlinear analysis of three-dimensional dynamic soil-structure interaction (SSI) of asymmetric buildings in time domain in order to evaluate the seismic response behavior of torsionally coupled wall-type buildings. The asymmetric building was idealized as a single-storey three-dimensional system resting on different soil conditions. The soil beneath the superstructure was modeled as nonlinear solid element. As the stiffness of the reinforced concrete flexural wall is a strength dependent parameter, a method for strength distribution among the lateral force resisting elements was considered. The response of soil-structure interaction of the system under the lateral component of El Centro 1940 earthquake record was evaluated and the effect of base flexibility on the response behavior of the system was verified. The results indicated that the base flexibility decreased the torsional response of asymmetric building so that this effect for soft soil was maximum. On the other hand, the torsional effects can be minimized by using a strength distribution, when the centre of both strength CV and rigidity CR is located on the opposite side of the centre of mass CM, and SSI has no effect on this criterion.

---

Abstract: This paper presents the influence of adding steel fibers and incorporation of silica fume on the mechanical properties of high-strength concrete. The variables investigated were steel fiber volume fraction (0 to 1.5%), silica fume replacement (5, 10 and 15%) and water-to-binder ratio (0.25, 0.30, 0.35 and 0.40). The influence of fiber content in terms of fiber reinforcing index on the compressive and splitting tensile strengths of high-strength steel fiber reinforce concrete (HSFRC) is presented. The use of silica fume increased both the compressive and splitting tensile strengths of concrete at 28 days. On the other hand, the addition of crimped steel fiber into high-strength concrete improves splitting tensile strength significantly. Based on the test data, using regression analysis, empirical expression to predict 28-day tensile strength of HSFRC in terms of fiber reinforcing index was developed and the absolute variation and integral absolute error (IAE) obtained was 3.1% and 3.3, respectively. The relationship between splitting tensile and compressive strength of SFRC was reported with regression coefficient (r) = 0.9. The experimental values of previous researchers were compared with the values predicted by the model and found to predict the values quite accurately.

---

This research shows the results of studies carried out to define and analyze the effect of aging on MSW behavior of Kahrizak Landfill, the biggest landfill in Iran. Studied samples consisted of fresh samples and also aged ones with 5.5, 14 and 21 years of age which were obtained by mechanical excavators in aged burial locations. Analyzing variation in MSW components illustrates that paste fraction of MSW decreases due to aging process while fibers show a rising trend. Also the moisture content and the organic content of MSW reduce below half of the initial values while the degree of decomposition (DOD) increase up to almost 60% after 14 years. These variations over the time are significantly related to the burying methods and environmental condition of burying location. Shear strength behavior of MSW material was analyzed by some CU tests using large scale triaxial apparatus (D=150mm, H=300mm) on remolded MSW specimens. General observations depict that with an increase in strain level, loading rises without any peak point on stress-strain curves. Fresh samples represent the lowest shear strength followed by 21, 14 and 5.5 year-old samples respectively. There is a direct relationship between fiber content and shear strength. Internal friction angle of aged samples decreases in comparison with fresh ones while cohesion has an inverse trend and rises over the time. According to the effect of burying condition on MSW characteristics, it seems that DOD factor is a more appropriate factor than age in order to analyze long-term behavior of MSW.

---

Rutting in asphalt concrete is a very common form of distress in asphalt concrete pavement which unfortunately has been incurable to date. One of the prime reasons of rutting is attributed to the behaviour of asphalt binder at elevated temperature. This study has investigated the performance of polypropylene fibres modified asphalt concrete mix against rutting. Two types of asphalt concrete samples were prepared namely control samples (those without polypropylene addition) and modified samples (with polypropylene modification). Marshall Mix Design was used for determining the Optimum Asphalt Content for both sample types. Slab asphalt concrete specimens of dimensions 300 mm length and breadth and 50 mm thickness were prepared for both control and modified samples. These samples were then tested in the Wheel Tracking Device for rutting susceptibility test. The samples were tested at four temperatures i.e. 40°C, 50°C, 55°C and 60°C and under the application of 10 000 load passes of 700N of axle load.. The polypropylene fibres were found to increase the Marshall Stability by almost 25%. The fibres were also determined to be effective against rutting at elevated temperatures while the modification was found to increase the Indirect Tensile strength by stiffening the mix at high temperature however at low temperature, the modification failed to perform effectively.

---

It was found out that the logarithmic models fit the cement–slag blend systems well. In the present study, based on the experimental results, a logarithmic model has been developed to predict the compressive strength of chemically activated high phosphorous slag content cement. Mixes of phosphorous slag (80 wt.%), Portland cement (14 wt.%) and compound chemical activator (6 wt.%) were prepared at different Blaine finenesses using a laboratory ball mill. Compressive strengths of mortar specimens cured in lime-saturated water were measured at different curing times. Mathematical model was prepared in terms of curing time and water-to-cement ratio as independent variables and compressive strength as dependent variable. The comparisons between the model reproductions and the experimentally obtained results confirm the applicability of the presented model.

---

The use of recycled bassanite, produced from gypsum wastes, in ground improvement projects is initiated recently in Japan to eliminate the huge quantities of gypsum wastes. Meanwhile the use of recycled bassanite has a positive effect on the environment and economy, it has many challenges. These challenges are related to the release of fluorine more than the standard limits results in contaminated fluorine soil. This research investigates the effect of the amount of bassanite, and water content on the release of fluorine from MC-clay soil stabilized with bassanite, taking in consideration their effect on the compressive strength. Recycled bassanite was mixed with furnace cement with a ratio of 1:1 to prevent the solubility of bassanite. Different amounts of this admixture were mixed with the tested soil at different water contents. Unconfined compression test was used to determine the compressive strength while the solubility of fluorine was used to represent the geo-environmental properties in term of the release of fluorine. Scan electron microscopic (SEM) test was done to identify the development of cementation compounds in the matrix of treated-bassanite soil. Test results showed that, the addition of bassanite had a significant effect on the improvement of compressive strength by increasing the amount of bassanite. Curing time had a significant effect on the increase of compressive strength, the strength increases with the increase of curing time, especially in the later curing time. The release of fluorine increases with increasing the amount of bassanite in soil mixture. The increase of water content had an indirect effect on the release of fluorine while it had a negative effect on the improvement of strength and consuming the amount of admixture. The increase of strength is associated with the decrease of the release of fluorine. Recycled bassanite, produced from gypsum wastes, had a potential to be used as a stabilizer material for MC-clay soil and meet the standards of environment.

---

To investigate the saturation induced collapse deformation behavior of rockfill material, a set of large-scale triaxial tests were conducted in saturated and dry-saturated conditions. Specimens were tested under various confining pressures. For dry-saturated tests, specimens were sheared in various stress levels. Results of all dry saturated tests indicate a sudden reduction in the specimen volume during the submerging process. The ratio of the minimum axial strength of a submerged specimen (at the end of the saturation process) to the shear strength of the specimen before saturation is defined as the coefficient of stress recovery, Csr. Results show that this ratio increases as the confining pressure increases, and decreases as the shear stress level increases. According to the results of dry-saturated tests, reduction values of the internal friction angle caused by saturation (c), the ratio of the elasticity modulus of the material after saturation to its elasticity modulus in dry condition, i.e., Ewet/Edry, and the saturation induced sudden volumetric strain (vc) decrease as the confining pressures increase. However the shear stress level does not have any meaningful effect on the variation of c, Ewet/Edry and (vc).

---

The Dynamic Probe is an effective tool used in site investigation. It is more economic than the use of direct drilling, particularly in explorations with moderate depth. This paper presents an experimental study to investigate the capability of using dynamic probing to evaluate the shear strength and compaction percent of fine soil. A series of dynamic probe tests were carried out at 6 different sites in the Khozestan, Hormozgan and Qom provinces in the central and southern regions of Iran. The repeatability of the results is considered and new empirical equations relating the dynamic point resistance to undrained shear strength and compaction percent are proposed. For undrained shear strength evaluation of fine soils, i.e. clay and silty clay soils, a reliable site-specific correlation between qd and Cu can be developed when considering the correlation between log qd and log Cu. Also compaction present can be evaluated by qd. These equations can be developed to provide site-specific relationships based upon geotechnical data at each new location. Using this approach an estimation of the undrained shear strength Cu and compaction percent CP can be determined from dynamic probe tests with acceptable accuracy. The present paper also encourages the wider application of dynamic probing for site investigation in fine soils.

---

This research paper presents the use of wasteful supplementary cementitious materials like fly ash and silica fume to conserve the cement used in concrete. The cement industry is one of the major producers of greenhouse gases and an energy user. In this study, Portland cement was used as a basic cementitious material. Fly ash and silica fume were used as the cement replacements by weight. The replacement levels of fly ash were 30%, 40% and 50%, and silica fume were 6% and 10%. The water binder ratio was kept constant as 0.4 and super plasticizer was added based on the required workability. Results of the binary and ternary concrete mixtures compressive strength, split tensile strength and flexural tensile strength were taken for studyup to 90 days. Based on the experimental results of compressive strength, prediction models were developed using regression analysis and coefficients were proposed to find the split tensile strength and flexural strength of binary-ternary concrete mixtures at 28 and 90 days.

---

This paper presents an investigation on durability of alkali-activated slag mortar against magnesium sulfate attack. To do so, the immersion tests in 5% magnesium sulfate solution under room temperature and wetting-drying cycles were applied. Mortar specimens from Portland cements type 2 and 5 in accordance to ASTM standard were also prepared and used as reference. The changes in compressive strength and length of specimens were measured at different time intervals and considered for evaluating the extent of degradation. After 360 days of exposure to the magnesium sulfate solution, type 2 and 5 Portland cements and alkali-activated slag cement have shown 61, 41 and 34% reduction in compressive strength and 0.093, 0.057 and 0.021% increase in length, respectively. The specimens were also studied by X-ray diffractometry and scanning electron microscopy for characterizing the chemical products of the degradation process. Main degradation products were ettringite and gypsum for Portland cements and gypsum for alkali-activated slag cement. According to the obtained results, alkali-activated slag cement exhibits a higher sulfate resistance compared to type 2 and even type 5 Portland cements

---

In this paper, an experimental study has been conducted on strengthening of reinforced concrete (RC) connections by FRP sheets. The innovation of this research is using narrow grooves on critical regions of connection to increase the adherence of FRP sheets and prevent their early debonding. Therefore, four RC connections were made and tested under a constant axial load on the column and an increasing cyclic load on the beam. The first specimen, as the standard reference specimen, had close tie spacing in ductile regions of beam, column and panel zone based on seismic design provisions, and the second specimen, as the weak reference specimen did not have these conditions in all regions. Two other weak specimens were strengthened using two different strengthening patterns with FRP sheets one by ordinary surface preparation and the other with surface grooving method for installing FRP sheets on the connection. The results showed that ultimate load and ductility of the weak specimen compared to standard specimen decreased 25% and 17%, respectively. The shear failure and concrete crushing were prevented in the ductile regions of the beam and panel zone in both strengthened specimens. Also, it was observed that early debonding of FRP sheets was prevented in the strengthened connection with grooving pattern and so had desirable ductility and bearing capacity similar to the standard specimen.

---

The paper presents the characterisation of an Algerian natural pozzolan (NP) intended to for use in cement-based materials. The experimental programme was based on different tests on paste and mortar. The pozzolanic activity was assessed by the means of lime consumption over time of mixtures of lime-pozzolan (75% NP and 25% Ca(OH)₂, water-binder ratio of 0.45). The degree of reactivity was assessed by observing the crystallographic changes (XRD) and lime consumption (TG) up to 1 year of hydration. The effect of NP on cement-based mixtures was based on the measurement of the water demand and setting time of pastes, and on the compressive strength of mortars, up to one year. The replacement rates of cement by pozzolan were 5, 10 and 15%. A superplasticizer was used (0, 1, 2 and 3% of the binder mass). A calculation of the carbon footprint was investigated in order to assess if the natural pozzolan could be considered as eco-efficient when used in replacement of the clinker. The results showed that NP had a medium pozzolanic reactivity and with a medium-low silica content. The use of NP usually led to a small increase in the water/binder ratio (up to 10%) to maintain constant workability. The setting time was also increased by around 20%. Nevertheless, strength tests showed that the pozzolan had sufficient activity to counteract the water demand, since long-term compressive strength of the binary system (cement + pozzolan) were higher than those of cement alone. The use of NP in replacement of clinker involves a reduction in CO₂ emissions for transport up to 1800 km, which is compatible with sustainable development. The results are most promising from both a performance-based and an environmental point of view