---

High performance and reliability of refurbish able knee braced steel frames has been confirmed in previous researches trying to get an optimal design for its configuration. Buckling of diagonal member which affects the hysteretic behavior of KBF under cyclic loadings has not been foreseen in previous evaluations of this system. This deficiency can be improved by utilization of adjustable rotary friction damper device (FDD) as knee element. Diagonal element buckling can be prevented considering a suitable value for FDD sliding threshold moment Mf. Lower values of Mf Lower energy dissipation rate in FDD and this leads to an optimization problem. Nonlinear time history analyses have been performed in addition to lateral cyclic loading analyses to evaluate the response of single story KBF subjected to seismic excitation. Optimal Mf in FDD has been chosen according to these analyses results. Roof displacement and acceleration, base shear and diagonal element’s buckling status have been compared in optimally designed KBF and FDD utilized KBF (FKBF) with different configurations. Nonlinear dynamic analyses have been performed for one, four, eight and twelve story frames under different seismic records with several PGAs. More than 60% displacement response reduction has been earned for the FKBF without considerable increase in base shear.

---

Abstract: This paper presents the influence of adding steel fibers and incorporation of silica fume on the mechanical properties of high-strength concrete. The variables investigated were steel fiber volume fraction (0 to 1.5%), silica fume replacement (5, 10 and 15%) and water-to-binder ratio (0.25, 0.30, 0.35 and 0.40). The influence of fiber content in terms of fiber reinforcing index on the compressive and splitting tensile strengths of high-strength steel fiber reinforce concrete (HSFRC) is presented. The use of silica fume increased both the compressive and splitting tensile strengths of concrete at 28 days. On the other hand, the addition of crimped steel fiber into high-strength concrete improves splitting tensile strength significantly. Based on the test data, using regression analysis, empirical expression to predict 28-day tensile strength of HSFRC in terms of fiber reinforcing index was developed and the absolute variation and integral absolute error (IAE) obtained was 3.1% and 3.3, respectively. The relationship between splitting tensile and compressive strength of SFRC was reported with regression coefficient (r) = 0.9. The experimental values of previous researchers were compared with the values predicted by the model and found to predict the values quite accurately.

---

An experimental study on the impact performance of silica fume concrete and steel fiber reinforced concrete at 28 days and 56 days under the action of repeated dynamic loading was carried out. In this experimental investigation, w/cm ratios of 0.4 and 0.3, silica fume replacement at 10% and 15% and crimped steel fibers with an aspect ratio of 80 were used. Results indicated that addition of fibers in high-performance concrete (HPC) can effectively restrain the initiation and propagation of cracks under stress, and enhance the impact strengths, toughness and ductility of HPC. Pulse velocity test was carried out for quality measurements of high-performance steel fiber reinforced concrete. Steel fibers were observed to have significant effect on flexural strength of concrete. The maximum first crack strength and ultimate failure strength at 28 days were 1.51 times and 1.78 times, respectively at 1.5% volume fraction to that of HPC. Based on the experimental data, failure resistance prediction model was developed with correlation coefficient (R) = 0.96 and absolute variation determined is 1.82%.

---

This paper describes experimental and numerical investigations on two specimens of frames composed of steel reinforced concrete beam and angle-steel concrete column under horizontal low cyclic loading. Based on the test results, the relationship curves of the horizontal load-displacement and the failure modes are acquired. Meanwhile the hysteretic behaviors, skeleton curves, stiffness degradation, energy dissipation, residential deformation of the two specimens are studied. Nonlinear structural analysis program OpenSEES is employed to predict the experimental curves. Using the verified numerical model, the influences of slenderness ratio, axial compression ratio, steel ratio of column, cross-section moment resistance of I-shaped steel in beam, ratio of longitudinal rebars of beam and prestressing level on skeleton curves are investigated. The results indicated that the two specimens exhibited the favorable ductility and energy dissipation capacity, and the beam depth could be reduced to improve service function because of the application of the prestress. The ultimate horizontal load decreases with the increase of column slenderness ratio, and firstly increases then decreases with the increase of axial compression ratio. In the meantime, the descent segment of skeleton curve is smooth with the increase of column slenderness ratio, and becomes steeper with the increase of axial compression ratio.

---

The effect of steel plate thickness on the repair effectiveness of RC beam is presented in this paper. A total of four beams were tested, one beam repaired by CFRP with a thickness of 1.2 mm and used as a control beam, and three beams repaired by a steel plate. Steel plates with a thickness of 2 mm, 3 mm, and 4 mm were used in repairing the beams. The maximum load-carrying capacity, deflection at mid span and edge of the opening, strain in steel bars, strain in externally bonded plates, crack patterns, and failure modes were observed on each beam. The externally bonded CFRP sheet and steel plates were found to be effective in the repairing of RC beams with large rectangular web opening. The results show that increasing steel plate thickness has little effect on the maximum load capacity. The CFRP plate is more effective than steel plate in increasing the load capacity of beams.

---

The linear and nonlinear responses of steel buildings with perimeter moment resisting frames (PMRFs) are estimated and compared to those of equivalent buildings with spatial moment resisting frames (SMRFs). The equivalent models with SMRFs are designed by using an approximated procedure in such a way that, not only their fundamental period, total mass and lateral stiffness are fairly the same as those of the corresponding buildings with PMRFs, but also other characteristics to make the two structural "as equivalent" as possible. The numerical study indicates that the interstory shears of the PMRFs building may be significantly larger than those of the SMRFs building. The main reasons for this are that the buildings with PMRFs are stiffer and that the dynamics properties of the two types of structural systems are different. The interstory displacements are similar for both structural systems in many cases. For some other cases, however, they are larger for the model with SMRFs, depending upon the closeness between the earthquake corner periods and the periods of the buildings. The global ductility and story ductility demands are larger for the buildings with PMRFs, implying that, since larger ductility demands are imposed, the detailing of the connections will have to be more stringent than for the buildings with SMRFs. It can be concluded, that the seismic performance of the steel buildings with SMRFs may be superior to that of steel buildings with PMRFs. The findings of this paper are for the particular models used in the study. Much more research is needed to reach more general conclusions

---

The current research intends to study the possibility of producing fiber recycled self-compacting concrete (FRSCC) using demolitions as a coarse aggregate (crushed red brick and crushed ceramic). Steel fibers were used in recycled self-compacting concrete (RSCC) to improve fresh and hardened properties of this type of concrete. Thirty nine concrete mixes were prepared to achieve the aim proposed in this paper. Steel fiber volume fraction varied from 0 to 2.0% by the volume of concrete with aspect ratio 65. The fresh properties of FRSCC were evaluated using slump flow, J-ring and V-funnel tests. Compressive strength, tensile strength, flexural strength and density tests were performed in order to investigate mechanical properties. The optimum volume fraction of steel fibers was 0.25% and 1.0% for the mixes contained crushed red brick and ceramic as a coarse aggregate respectively. At optimum content of steel fibers, the compressive strength for the RSCC mixes with steel fibers improved by 11.3% and 31.8% for the mixes with crushed ceramic and crushed red brick, respectively with respect to control mix. Also the tensile strength and the flexural strength for the mixes were improved

---

This paper presents a finite element analysis and its related experimental test of corrugated steel web beams subjected to fatigue loading. A particular focus in this study was set on the fatigue failure arising from the web-to-flange welded joint of the corrugated steel web beam. A detailed three-dimensional finite element model which explicitly includes the geometry of the web-to-flange welds along the corrugated web was developed to simulate the test corrugated web beam. The finite element model is verified by comparing with related fatigue experimental test results. The effective notch stress approach was also applied to analyse the web-to-flange welded joint replicating the local critical region in the corrugated web beam. The fatigue strength of the web-to-flange welded joint was evaluated and compared numerically by considering the stress distribution at potential fatigue crack initiation location. The fatigue life of the corrugated web beam was assessed numerically by incorporating material S-N relation and employing fracture mechanics approach. The comparison with the fatigue test results show that it is possible to expect the fatigue crack failure arising at the weld root or weld toe corresponding to the sections with reference angle using the effective notch stress analysis. The range of these predictions was evaluated by comparing with fatigue test results with accuracy and can be considered between AASHTO fatigue categories B and B’. The parametric notch stress analysis incorporating the influences of corrugation angle was performed and demonstrates it is possible to expect the fatigue crack failure arising at the weld root or weld toe. Finally, a practical solution for possible fatigue life enhancement of such structure is proposed by decreasing the corrugation angle or smoothing the intersection geometry of the corrugated web is suggested together with a moderate increase of the flange thickness.

---

Steel-concrete hybrid systems are used in buildings, in which a steel structure has been placed on a concrete structure to make a lighter structure and have a faster construction. Dynamic analysis of hybrid structures is usually a complex procedure due to various dynamic characteristics of each part, i.e. stiffness, mass and especially damping. Dynamic response of hybrid structures has some complications. One of the reasons is the different stiffness of the two parts of structure and another reason is non-uniform distribution of materials and their different features such as damping in main modes of vibration. The available software is not able to calculate damping matrices and analyze these structures because the damping matrix of these irregular structures is non-classical. Also an equivalent damping should be devoted to the whole structure and using the available software. In the hybrid structures, one or more transitional stories are used for better transition of lateral and gravity forces. In this study, an equation has been proposed to determining the equivalent uniform damping ratio for hybrid steel-concrete buildings with transitional storey(s). In the proposed method, hybrid buildings are considered to have three structural systems, reinforced concrete, transitional storey and steel. Equivalent uniform damping ratio is derived by means of a semi-empirical error minimization procedure.

---

Steel plate shear walls have long been used as a lateral load resisting system. It is composed of beam and column frame elements, to which infill plates are connected. This paper investigates the progressive collapse-resisting capacity of 50-story building 3D model of the strip model of steel plate shear wall comparing with X-braced and moment frame system based on the removing structural elements from a middle and corner of the exterior frame, in the story above the ground. The collapse behavior is evaluated by different nonlinear static and dynamic analyses using conventional analysis software. In this study, vulnerability of structures is also assessed by sensitivity index (SI) regarding the sensitivity of structures to dynamic effect induced by progressive collapse. To identify vulnerable members, resulting actions of nonlinear static analysis, considering load factor to account for dynamic effect, at the failure mode of structure at the specific performance level are compared by the factor of redundancy related to overall strength of structure, with the linear static analysis of damaged model without considering dynamic effect,. Comparing analysis results indicated that in the steel plate shear wall system, the progressive collapse resisting potential is more than X-braced and moment frame. Sensitive index of highly sensitive elements to dynamic effect stated that in the structural models, beams are more vulnerable in moment frame than X-braced frame and SPSW structure, significantly, and vulnerability of columns in X-braced frame and SPSW system is more than moment frame.

---

This study is devoted to investigate the effects of mass eccentricity in seismic responses of base-isolated structures subjected to near field ground motions. Superstructures with 3, 6 and 9 stories and aspect ratios equal to 1, 2 and 3 have been idealized as steel special moment frames resting on a reasonable variety of Triple Concave Friction Pendulum (TCFP) bearings considering different period and damping ratios for the isolators. Three-dimensional linear superstructure mounted on nonlinear isolators are subjected to 3 components of near-field ground motions. Under 25 near-field ground motions, effects of mass eccentricity on the main system parameters are studied. These parameters are selected as the main engineering demands including maximum isolator displacement and base shear as well as peak superstructure acceleration. The results indicate that the mass eccentricities has not a remarkable effect on isolator displacement. In contrary to displacement, torsional effect of mass eccentricity raise the base shear up to 1.75 times in a three-story superstructure. Additionally, mass eccentricity can amplify the roof acceleration of a nine-story model approximately 3 times in comparison with a symmetric superstructure. It is also concluded that eccentricity in the direction of the subjected earthquake has the most impact on base shear while the isolator displacement and roof acceleration has mostly influenced by the eccentricity perpendicular to the earthquake path.

---

Steel bridges play a very important role in every country’s transportation system. To ensure that bridges perform reliably, engineers monitor their performance which is referred to as Structural Health Monitoring (SHM). An important element of SHM includes the prediction of service life. There is ample historical evidence that bridge damage is pervasive and their life time is decreasing. To manage costs and safety, service life prediction of bridges is necessary. We present a statistical method to predict service life for steel bridges. A nonparametric statistical model based on the bootstrap method for stress analysis for fatigue life prediction of steel girder bridges is proposed. The bootstrap provides a simple approach for reproduction of the probability distribution of measured strain data. The bootstrap is sensitive to the number of events in the verification sample (data), thus we introduce a stable survival distribution function (SDF). An index is presented in this paper for inferring the service life of steel bridges, which can be known as the Life Index (µ). The life index function shows variation of the age of steel bridges under daily traffic loads. A regression model is developed which relates the service life of steel bridges using a bridge life index based on measured operational strain time histories. The predicted remaining service life derived from the model can contribute to effective management of steel bridges. The proposed method assists bridge engineers, bridge owners, and state officials in objective assessment of deteriorated bridges for retrofit or replacement of deteriorated bridges. Timely repair and retrofit increase the safety levels in bridges and decrease costs.

---

The seismic performance levels are discrete damage states selected from among the infinite spectrum of possible damage states that buildings could experience as a result of earthquake response. The observation of building damage during strong motion earthquakes showed that correlation of structural damage with a single parameter such as peak ground acceleration or the total seismic duration is low while peak ground acceleration is often used as a main seismic parameter to evaluate seismic performance of structures. Main objective of this study is to determine the relationship between several seismic acceleration parameters and the Target Displacement (TD) of steel frame structures, which is an important parameter to identify performance levels. For this purpose, first, nonlinear analysis is performed on the SAC 3- and 9-story frames subjected to several far-field earthquakes and then target displacements and seismic parameters are calculated for each structure.The relationship between the target displacement and seismic parameters is evaluated in the form of correlation coefficient. It is shown that PGA has poor correlation with the target displacement. On the other hand, HOUSNER intensity, spectral pseudo-acceleration, spectral pseudo-velocity and peak ground velocity exhibit strong correlation with TD.

---

From practical point of view, optimum design of structures under time variable loadings faces many challenges. Issues such as time-dependent behavior of constraints and the computational costs of the gradients could be mentioned. In order to prevent such difficulties, in this paper, response spectrum method has been utilized instead of applying direct time history method. Additionally, seismic design of structures is defined as a design for a specific response spectra not for an individual acceleration time history. Furthermore, here, in order to guarantee the global optimal designs, the obtained results from gradient-based method are compared with those from the discrete optimization technique (Genetic algorithm). As well, the P-Delta effects are considered in a seismic analysis. In addition, many practical constraints according to the Iranian national building code (NBC) are included in the optimization problem. The developed MATLAB based computer program is utilized to solve the numerical examples of low, intermediate and relatively high-rise braced and un-braced steel frames.

---

In this paper, the assessment of four short-span steel bridges from 24 to 42 m under local overloaded trucks and ground motion records are presented and discussed. Bridges were virtually located in Mexico, and so the vehicular live loads, earthquake loads due to local seismicity, and other local loads were adapted in the design. A realistic condition of the local design truck for Mexico was selected from survey traffic flows reported for local highways. Nonlinear dynamic analyses were carried out using seven historical records associated with the largest vertical intensities from subduction earthquakes in Mexico. Results are intended to evaluate the local practice, which frequently adopts the current AASHTO LRFD Specifications in the absence of an official local design code for bridge structures. Thus, this research pretends to provide design recommendations for short-span steel bridges in Mexico.

---

In this study, a comparison is made between force and displacement controlled non-linear FE analyses for an RC beam in flexure with partially developed steel bars. An FE model with slightly unsymmetrical reinforcement was analyzed by applying two-point loading using both force and displacement controlled methods. The responses obtained using ANSYS-13 were validated against available experimental data. Combined comparative display of flexural response of the beam using force and displacement controlled analysis, that has least been addressed in the literature, is given here. Study choses large-deformation-nonlinear plastic analysis scheme, discrete modeling approach for material modeling and program-chosen incremental scheme following Newton-Raphson method. The results show that displacement controlled approach is efficient in terms of time saving and less disk space requirement along with the ability to give falling branch of load-deflection response, if element displacement capacity still exists. Moreover, it gives an early estimate of the load carrying capacity of the structural element along with suitable values of convergence and non-linear solution parameters. However, for a beam with unsymmetrical detailing, force controlled analysis method seems to yield more realistic and practical results in terms of mid span deflection and beam cracking behavior compared with assumed symmetric displacement controlled technique. It also gives true fracture prediction at ultimate load level, which is not true for the displacement controlled method as the computer code forces the model to maintain equal displacements at two load points, falsely increasing the capacity of the beam.

---

The paper is presented an attempt to assess service life of steel girders in military bridges (or by-pass temporary bridges) when fatigue cracks are detected in them. A function describing the geometry of fatigue cracks, the so-called crack shape factor Y, for two different, assumed calculated models, was presented. The function was used to plot sample graphs allowing assessing the remaining service life of such structural elements or engineering structures in a simple way. This method of analyzing can be used not only for the military bridges but also for other steel structures with existing cracks. The work is also presented assessments of possible applications of two FEM calculated models using shell elements to test stress and deformation at the top part of a fatigue crack located in a web of a steel girder used in the military bridges. The results of the conducted numerical analyses were compared with the results obtained in experimental research conducted in laboratory conditions using extensometers.

---

In this paper, the probabilistic seismic performance of vertically irregular steel buildings, considering soil-structure interaction effects, is evaluated. Various irregular distributions of structural properties, including mass, stiffness and strength along the height of three-dimensional moment resisting steel frames were intended. The finite element model of soil medium was created with solid elements below the structure. The nonlinear material behavior of soil was considered as well. Nonlinear incremental dynamic analysis was performed to evaluate the flexible-base structural performance in the framework of probabilistic performance-based earthquake engineering. According to the median curves of intensity-demand of structures, it is concluded that non-uniform height-wise distribution of lateral resistance properties of steel structures varies the displacement demand and the seismic capacity of the irregular frames, compare to the regular structure. The capacity variation of most irregular frames is more obvious at the nonlinear phase of structural behavior. Due to the foundation flexibility, the damage concentration raises in the bottom floor and the irregularity increase the seismic demands of the lower floors of the system. Among all the irregular steel frames, the average increase of the displacement demand and reduction of the seismic capacity are maximal for the strength and concurrent variation of stiffness and strength irregularity models, respectively. Additionally, mass irregularity shows minor influence in the seismic demand and capacity variations of the steel frames. The predominant influence of stiffness and strength irregularities (soft and weak story) is observed in reduction of the structural ductility factor and the mean annual frequency of exceeding limit states.

---

This paper presents an evaluation on lateral cyclic behaviors of precast concrete columns using a steel box connection through experimental investigation. The test consisted of one monolithic reinforced concrete column as a reference and five precast concrete columns. All specimens had identical dimensions of 0.25 x 0.25 m2 cross sectional area and 1.7 m in height with a longitudinal reinforcement ratio of 0.0152. Materials used for all specimens were also from the same batch. The study was aimed at understanding the design concept of the steel connecting box and detailing of column reinforcement for avoiding the brittle failure of precast concrete frame buildings. The experimental results show that without premature failure in welding or nut slipping, depending largely on the reinforcement details, the precast system with a steel box connection can be effectively used. Flexural failure mode with a ductile mechanism can be achieved to resemble the monolithic one. With a higher relative stiffness and capacities of the designed connecting box, the precast columns show a higher capacity as the failure section was shifted to an upper level. Hence, it can be said that the proper details of precast concrete columns contain acceptable seismic performances e.g. ultimate capacity, stiffness, energy dissipation, and capacity degradation under repeated loading.

---

This study presents methods for numerical modelling and the static computer analysis of steel decks fixed on scaffoldings. The main problem raised here is the method of creating models of a single deck and determination of the accuracy of every model for various design situations: the analysis of state stress in components of decks, the strength analysis of scaffolding where decks can be loaded by untypical the arrangement of materials and the strength analysis of full scaffoldings. The analysis of a state stress in components of a deck requires a detailed model. The analyses of scaffoldings with load by materials have to be performed with using more simple models of platforms. The static-strength analysis of full scaffoldings with many frame elements can be performed if the simplest models of decks are used. In this paper the sets of truss elements replace the stiffness of scaffolding decks.