International Journal of Industrial Engineering & Production Research
Iran University of Science & Technology
Tue, Dec 24, 2024
[Archive]
Volume 30, Issue 3 (IJIEPR 2019)
IJIEPR 2019, 30(3): 245-254 |
Back to browse issues page
Download citation:
BibTeX | RIS | EndNote | Medlars | ProCite | Reference Manager | RefWorks
Send citation to:
BibTeX | RIS | EndNote | Medlars | ProCite | Reference Manager | RefWorks
Send citation to:
Rizvi S A, Wajahat A. Integration of grey-based Taguchi technique in optimization of parameters process during the turning operation of 16MnCr5 steel. IJIEPR 2019; 30 (3) :245-254
URL: http://ijiepr.iust.ac.ir/article-1-893-en.html
URL: http://ijiepr.iust.ac.ir/article-1-893-en.html
1- Mechanical Engineering Department, SCRIET(CCS University).Meerut, India. , saritbhu@gmail.com
2- Mechanical Engineering Department, SCRIET(CCS University).Meerut, India.
2- Mechanical Engineering Department, SCRIET(CCS University).Meerut, India.
Abstract: (4217 Views)
CNC turning is widely used as a manufacturing process through which unwanted material is removed to get the high degree of surface rough. In this research article, Taguchi technique was coupled with grey relation analysis (GRA) to optimize the turning parameters for simultaneous improvement of productivity, average surface roughness (Ra), and root mean square roughness (Rq).Taguchi technique L27 (34) orthogonal array was used in this experimental work. Feed, speed, and depth of cut were considered as the controllable process parameters. average roughness (Ra), root mean square roughness (Rq),and material removal rate (MRR) were considered as the performance characteristic and from TGRA result, it was revealed that the optimum combinational parameters for multi-performance, based on mean response values and confirmation experiments with Taguchi-based GRA is A1B1C1 (Vc=400 rpm, f=0.06 mm/rev, and DOC=0.5 mm). The optimum values obtained from experimental investigations for Ra was 6.86 μm, and MRR was 20690.31 mm3/s,further analysis of variance(ANOVA) were applied and it was identified that the depth of cut having most significant effect followed by speed and feed for multiresponse optimization. The percentage contribution of depth of cut was 38.28.71 %, speed was 11.89 % and feed was 8.466 %.
CNC turning is widely used as a manufacturing process through which unwanted material is removed to get a high degree of surface roughness. In this research article, Taguchi technique was coupled with grey relation analysis (GRA) to optimize the turning parameters for simultaneous improvement of productivity, the average surface roughness (Ra), and root means square roughness (Rq). Taguchi technique L27 (34) orthogonal array was used in this experimental work. Feed, speed, and depth of cut were considered as the controllable process parameters. average roughness (Ra), root mean square roughness (Rq), and material removal rate (MRR) were considered as the performance characteristic and from TGRA result, it was revealed that the optimum combinational parameters for multi-performance, based on mean response values and confirmation experiments with Taguchi-based GRA is A1B1C1 (Vc=400 rpm, f=0.06 mm/rev, and DOC=0.5 mm). The optimum values obtained from experimental investigations for Ra was 6.86 μm, and MRR was 20690.31 mm3/s, further analysis of variance(ANOVA) were applied and it was identified that the depth of cut having most significant effect followed by speed and feed for multiresponse optimization. The percentage contribution of the depth of cut was 38.28.71 %, speed was 11.89 % and feed was 8.466 %.
CNC turning is widely used as a manufacturing process through which unwanted material is removed to get a high degree of surface roughness. In this research article, Taguchi technique was coupled with grey relation analysis (GRA) to optimize the turning parameters for simultaneous improvement of productivity, the average surface roughness (Ra), and root means square roughness (Rq). Taguchi technique L27 (34) orthogonal array was used in this experimental work. Feed, speed, and depth of cut were considered as the controllable process parameters. average roughness (Ra), root mean square roughness (Rq), and material removal rate (MRR) were considered as the performance characteristic and from TGRA result, it was revealed that the optimum combinational parameters for multi-performance, based on mean response values and confirmation experiments with Taguchi-based GRA is A1B1C1 (Vc=400 rpm, f=0.06 mm/rev, and DOC=0.5 mm). The optimum values obtained from experimental investigations for Ra was 6.86 μm, and MRR was 20690.31 mm3/s, further analysis of variance(ANOVA) were applied and it was identified that the depth of cut having most significant effect followed by speed and feed for multiresponse optimization. The percentage contribution of the depth of cut was 38.28.71 %, speed was 11.89 % and feed was 8.466 %.
Type of Study: Research |
Subject:
Optimization Techniques
Received: 2019/04/14 | Accepted: 2019/06/9 | Published: 2019/09/16
Received: 2019/04/14 | Accepted: 2019/06/9 | Published: 2019/09/16
Send email to the article author
| Rights and permissions | |
 | This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License. |
