Mehryab A., Arabi H., Tamizifar M., Seyedein S.h., Razazi M.a.,
Volume 2, Issue 1 (3-2005)
Abstract
In this research, the mechanism of joining three sheets of metals, i.e. brass-steel-brass, by cold roll welding process has been studied. For this purpose, the two surfaces of steel sheets were roughened with stainless steel wire brush by different amounts, then the brass sheets were put on both sides of the steel sheets, before they were subjected to cold roll process. During rolling, peaks of the asperities on the surfaces of the steel sheet were pressurized, i.e. deformed, much more than that of trough. Hence, more hardening due to formation of higher dislocation density in the peaks regions were detected in comparison to the trough regions. Therefore, due to the differences in the amounts of work hardening occurred during cold rolling in the peaks & trough of the scratches and also due to the nature of the rough surfaces of the steel sheets, which causes the smooth surface of soft brass sheets laied over the rough surface of the steel sheet to be shappend according to the profile of the steel sheet scratches during cold rolling, mechanical locking occurred at the interface of brass & steel sheets. In addition, while the extrusion of brass took place through cracks within the surface of hardend peaks and metal bonding occurred on the contact points of the brass sheet & the vergin steel. Therefore, it seems two mechanisms were in operation is making a suitable joining between the sheets. One was a locking mechanism due to the roughness of the steel sheets & the other was bonding mechanism due to the bonding between the peak points of the scratches &soft brass surface. The strength of the bonded points in the interface were later increased by annealing the composite, so that by annealing the samples within the 500-900°C range for aperiod of 1 1/2 hr the interface strength increase substantially. The results of peeling test indicated that the interface strength of the samples annealed at 700°C or more increased so much that the brass sheet toms during peeling & the fracture did not pass through the interface.
A. A. Babakoohi Ashrafi, H. Mohammadi, A. Habibolla Zade,
Volume 13, Issue 2 (6-2016)
Abstract
In this paper, the influence of heat treatment on PH17-7 stainless steel spring was evaluated. Precipitation hardening phenomenon of PH 17-7 steel was evaluated in three stages. First, the spring constant changes with time and temperature was evaluated. Second, the spring constant changes with respect to its original length at constant temperature and time with blocking (spring length after compression, 18 and 21 mm) were investigated. And finally, the spring heat treatment at 480 °C for 80 min and then holding at 230 °C in oil bath for 60 min without blocking were investigated. The results showed that the use of 18 mm block have large spring constant than 21 mm block. The optimal conditions (480°C for 80 min) for this spring to reaching maximum spring constant were determined.
Saleheh Abbaspoor, Farhang Abbasi, Samira Agbolaghi,
Volume 19, Issue 2 (6-2022)
Abstract
Single crystals of double crystalline block copolymers of poly(ethylene glycol) (PEG)-b-poly(ε-caprolactone) (PCL) and PEG-b-poly(L-lactide) (PLLA) were grown from dilute solution in homo- and mixed-brush systems. Crystallization behavior of biodegradable one end-restricted crystallizable PCL and PLLA chains in homo- and mixed-brush nanostructures were investigated. Chemical and physical circumstances of crystallizable brushes were altered. Physical environment was adjusted by amorphism/crystallinity and rigidity/flexibility of neighboring brushes. Chemical environment was manipulated by interaction and miscibility of various brushes. Distinct single crystals were grown with mixed-brushes of amorphous-crystalline (polystyrene (PS), poly(methyl methacrylate) (PMMA), PCL and PLLA, double crystalline (PCL/PLLA), and rod-crystalline polyaniline (PANI)/PCL or PLLA. Surrounding was only effective on hindrance or nucleation commencement of crystallization for crystallizable brushes and had no effect on crystallization features. Novel three-layer fully single crystalline nanostructures, whose characteristics were fixed via changing the crystallization temperature, were also developed. For long crystallizable tethers, crystallization increased both brush and substrate thicknesses.
