Showing 12 results for Tensile
Mir Habibi A.r., Mir Habibi A.r., Mir Habibi A.r.,
Volume 1, Issue 1 (3-2004)
Abstract
The continuity and thickness of the coating layer, are the most important factors in wetting properties and strength of carbon fibers. These factors are crucial in the quality of metal matrix composites made with carbon fibers. In this research the Polyacrylonitrail base carbon fibers have been nickel coated with 0.2, 0.5, 0.8 and 11 ,u in thickness, by the electroless method. The effect of the thickness of nickel coating on surface condition and also the tensile strength of the carbon fibers has been investigated. The study of surface condition of the coated carbon fibers by SEM showed that the nickel coating at the thickness of about 0.5 pin has the best continuity oil the carbon fibers. The results of tensile tests of carbon fibers coated with different thickness of nickel showed that increasing the thickness of coating layer decreases the overall strength of fibers.
A.nouri, Sh.kheirandish, H. Saghafian,
Volume 5, Issue 4 (12-2008)
Abstract
Abstract: In the current work, the strain hardening behavior of dual-phase steels with different silicon content (0.34-
2.26 Wt. %) was examined using the modified Crussard-Jaoul analysis. It was shown that these dual-phase steels
deform in two stages over a uniform strain range. Each stage exhibited a different strain hardening exponent varying
with silicon content. At the first stage, work hardening exponent remind significantly constant, while during the second
stage, it decreased with increasing silicon content from 0.34% to 1.51% and then increased for the higher silicon
contents (1.51% to 2.26%). It was found that the strain hardening behavior of these steels was predominantly affected
by the volume fraction of martensite at low silicon contet and the ferrite strengthening induced by silicon at the higher
silicon content. The effect of silicon content on the volume fraction of martensite and tensile properties were also
considered.
H. Nosraty, M. Tehrani-Dehkordi, M. M. Shokrieh, G. Minak,
Volume 12, Issue 1 (3-2015)
Abstract
In this study, the tensile and compressive behaviors of pure and hybrid composite laminates reinforced by
basalt–nylon bi-woven intra-ply fabrics were experimentally investigated. Epoxy resin was used as the matrix material.
The purpose of using this hybrid composite is to obtain superior characteristics by using the good strength property
of basalt fiber with the excellent toughness of nylon fiber. Five different types of woven fabric were used as
reinforcement with different volume percentages of nylon (0%, 25%, 33.3%, 50% and 100%). The effects of
nylon/basalt fiber content on tensile and compressive parameters were studied. In addition, the after failure visual
inspection and scanning electron microscopy (SEM) analysis was used to determine the extent and type of damage on
tested specimens. The results indicate that the tensile and compressive performances of these composites are strongly
affected by the nylon/basalt fiber content. Also, with a proper choice of fiber content, the nylon/basalt hybrid
composites can achieve mechanical properties comparable with the pure ones. The stress–strain curves, after failure
visual inspection and SEM analysis of tested specimens reveal that hybridization can prevent catastrophic and
complete failure. In hybrid composites, the basalt and nylon fibers cannot reach their maximum strength at the same
time and the progressive failure of the various fibers therefore occurred
M. Senthil Kumar , R. V. Managalaraja, K. Senthil Kumar, L. Natrayan,
Volume 16, Issue 2 (6-2019)
Abstract
The present requirement of automobile industry is seeking lightweight material that satisfices the technical and technological requirements with better mechanical and tribological characteristics. Aluminium matrix composite ( AMC ) materials meet the requirements of the modern demands. AMCs are used in automotive applications as engine cylinders, pistons, disc and drum brakes. This paper investigates the effect of particle size and wt% of Al2O3/SiC reinforcement on mechanical and tribological properties of hybrid metal matrix composites (HMMCs). AA2024 aluminium alloy is reinforced with Al2O3/SiC different particle sizes (10, 20 and 40 µm) and weight fractions (upto 10 wt %) were fabricated by using squeeze casting technique. HMMCs were characterized for its properties such asX-ray diffraction (XRD), density, scanning electron microscope ( SEM ), hardness, tensile strength, wear and coefficient of friction. AA2024/5wt%Al2O3/5wt%SiC with 10 μm reinforced particle size showed maximum hardness and tensile strength 156.4 HV and 531.43 MPa and decrease in wear rate was observed from from 0.00307 to 0.00221 for 10N. Hybrid composites showed improved mechanical and wear resistance suitable for engine cylinder liner applications.
I. Hajiannia, M. Shamanian, M. Atapour, R. Ashiri, E. Ghassemali,
Volume 16, Issue 2 (6-2019)
Abstract
In this study, the effects of the second pulse resistance spot welding on the microstructure and mechanical properties of TRIP1100 steel were evaluated. The thermal process after welding was designed to improve metallurgical properties with pulse currents of 6kA, 9kA and 12kA after initial welding with 10kA current. The effect of the second pulse on mechanical and microstructural properties was investigated. The fracture of the welds was for pulsed samples of 6kA and 9kA PO with CTS test. Due to existence of the microstructure including the equaxial dendritic and finer in FZ in the pulsed current 9kA, the maximum fracture energy and maximum force were observed. A significant decrease in the FZ hardness in 6kA current was observed in the nanohardness results, which was attributed to existence martensitic and ferrite temper. The highest ratio of CTS / TSS was obtained for 6kA and 9kA, respectively, and force displacement rate was maximum in 9kA. The fracture surfaces included dendrites and dimples. The results of partial fracture revealed separation in the coherent boundaries of the coarse grain of the annealed region.
A. Khakzadshahandashti, N. Varahram, P. Davami, M. Pirmohammadi,
Volume 16, Issue 3 (9-2019)
Abstract
The combined influence of both melt filtration and cooling rate on the microstructure features and mechanical properties of A356 cast alloy was studied. A step casting model with five different thicknesses was used to obtain different cooling rates. The effect of melt filtration was studied by using of 10 and 20 ppi ceramic foam filters in the runner. Results showed that secondary dendrite arm spacing decreased from 80 μm to 34 μm with increasing cooling rate. Use of ceramic foam filters in the runner led to the reduction of melt velocity and surface turbulence, which prevented incorporation of oxide films and air in the melt, and consequently had an overall beneficial effect on the quality of the castings. A matrix index, which is the representative of both SDAS and microporosity content, was defined to consider the simultaneous effect of melt filtration and cooling rates on UTS variations. Also, the fracture surface study of test bars cast using 10 and 20 ppi ceramic foam filters showed features associated with ductile fracture.
R. Niazi, E. Tohidlou, H. Khosravi,
Volume 17, Issue 3 (9-2020)
Abstract
The effects of erbium (Er) addition at various weight percentages (0-0.6 wt.% at an interval of 0.2) on the microstructural characteristics, tensile response and
wear properties of as-cast Al-7.5Si-0.5Mg alloy were evaluated. The microstructure of samples was examined by X-ray diffraction, optical microscopy and scanning electron microscopy. The obtained results demonstrated that the incorporation of erbium obviously decreased the α-Al grain size and eutectic Si, and altered the Si morphology from plate to semi-globular. Further addition of erbium (> 0.2 wt.%) did not alter the eutectic morphology and size. Moreover, the Al
3Er phase was also observed in the eutectic region after modification. Out of the erbium contents used, 0.2 wt.% erbium showed the best influence on the tensile and wear properties. Compared with those of unmodified specimen, the values of ultimate tensile strength and elongation were enhanced by 31% and 39%, respectively with the introduction of 0.2 wt.% erbium. Additionally, a remarkable enhancement in the wear properties was observed with the addition of 0.2 wt.% erbium.
Zahra Rousta, Esmaeil Tohidlou, Hamed Khosravi,
Volume 18, Issue 1 (3-2021)
Abstract
This study deals with the effects of erbium (Er) addition on the microstructural evolution and tensile properties of Al-Mg2Si in-situ metal matrix composites. The morphology of primary Mg2Si and eutectic phases were observed in details using optical microscope and scanning electron microscopy (SEM). The results showed that the increase of Er content has a slight effect on the size and morphology of primary Mg2Si phases, but the eutectic structure evolves from the coarse structure into the fine one. Also, with Er addition the eutectic mixtures of Al and Mg2Si with fibrous morphology has been developed instead of the flake like Al-Mg2Si eutectic microstructure. Meanwhile, Al3Er phase was observed in the samples containing Er. The ultimate tensile strength (UTS) of the composite changes under the various content of Er. The maximum strength was found at the 0.6 wt% Er with the fine eutectic microstructure. The study of SEM micrographs from the fracture surface of composites revealed that Er addition changes the fracture mode from brittle to ductile one with fine dimples. The mechanism of microstructural evolution was discussed in details.
Reza Soleimani Gilakjani, Seyed Hossein Razavi, Masoumeh Seifollahi,
Volume 18, Issue 1 (3-2021)
Abstract
Niobium addition is an appropriate approach for improvement of superalloy’s operation. The purpose of this study is twofold: (1) to investigate on the η and γ/ phase precipitations along with (2) to identify the high-temperature tensile properties in A286 and Nb-A286, as a modified type. The heat treatment of both alloys was carried out in a two-stage aging procedure at 760°C for 16 h and 820°C for 2 to 30 hours, following characterized by optical and Scanning electron (SEM-EDS) microscopies, differential thermal analysis (DTA) and high temperature tensile tests. The results showed that niobium addition was increased the volume fraction of γ/ phase, from 10.7% to 12%, decreased its size, from 94 to 71 nm, and rising the γ/-dissolution temperature from 987°C to 1007°C. Moreover, the γ/ to η phase transformation was sluggishly occurred in Nb-A286 due to more stable of γ/ precipitations. Furthermore, the Nb-A286 alloy demonstrates higher mechanical properties than A286 one, approximately 100MPa improvement, which it was contributed to the much large volume fraction and finer size of more stabilized γ/ phase.
Mitra Ghannadi, Hediye Hosseini, Bagher Mohammad Sadeghi, Bahman Mirzakhani, Mohammad Tahaaha Honaramooz,
Volume 18, Issue 3 (9-2021)
Abstract
The objective of the present paper is to investigate the effects of rapid heating and cryogenic cooling on on the microstructure and tensile properties of Al-Cu-Mg. The specimens were subjected to three heat treatment cycles in which the Infrared heating (IR) were used as the heating medium at the ageing stage, and the liquid nitrogen and water were used as the quenching mediums. The ageing temperature and time were 190⁰C and from 2 hours to 10 hours, respectively.The results indicated that by using IR at the ageing stage, the hardening rate enhanced because the rapid heating via this method leads to faster diffusion of the alloying elements. Moreover, the high density of nano-sized precipitates formed during ageingleads to higher strength and suitable ductility. Cryogenic treatment showed a negligible effect on both microstructure and tensile properties; however, it improved ductility. Overall, the combination of a high heating rate and cryogenic treatment led to the highest mechanical properties. SEM micrograph of the fracture surface of alloy demonstrated that in Cryogenic treatment+Artificial Ageing (CAA) condition, the surface had been fully covered by deep dimples in contrast to the Cryogenic treatment+Infrared Heating (CIR) and Water-Quench+ Infrared Heating (QIR) conditions which their dimples were shallow and also some facets were observed.
Dillibabu Surrya Prakash, Narayana Dilip Raja,
Volume 18, Issue 4 (12-2021)
Abstract
Hybrid composites consisting of AA6061 matrix reinforced with TiB2 (2, 4, 6, and 8 wt. %), Al2O3 (2 wt. %) particles were produced by the sintering process. In comparison to the base material AA6061, the composite produced had improved mechanical properties. The sintered composites' mechanical properties, such as tensile strength and hardness, are measured and compared to the wear-tested specimen. Optical micrographs reveal that composites were riddled with defects like blowholes, pinholes, and improper bonding between the particulates before sintering. However, the post-sintered optical micrograph showed that the defects were greatly suppressed. Micrographic images revealed the changes in surface characteristics before and after wear. Until a sliding distance of 260 m, the wear rate of the hybrid composites was kept lower than that of the base material. The coefficient of all the composite materials produced for this study was noted to be less than that of the base material. The results reveal that the hardness of hybrid composites having 4 wt. % and 6 wt. % of TiB2 particulates increased by 5.98 % and 1.35 %. Because of the frictional heating during the wear test, the tensile properties lowered by up to 49.6%. It is concluded that the hybrid composites having 4 wt. % and 6 wt. % of TiB2 particulates exhibited less wear rate for extended sliding distance, good hardness, moderate tensile strength, and decent elongation percentage compared to its counterparts.
Imtiaz Ali Soomro, Srinivasa Rao Pedapati, Mokhtar Awang, Afzal Ahmed Soomro, Mohammad Azad Alam, Bilawal Ahmed Bhayo,
Volume 19, Issue 4 (12-2022)
Abstract
This paper investigated the optimization, modelling and effect of welding parameters on the tensile shear load bearing capacity of double pulse resistance spot welded DP590 steel. Optimization of welding parameters was performed using the Taguchi design of experiment method. A relationship between input welding paramaters i.e., second pulse welding current, second pulse welding current time and first pulse holding time and output response i.e, tensile shear peak load was established using regression and neural network. Results showed that maximum average tensile shear peak load of 26.47 was achieved at optimum welding parameters i.e., second pulse welding current of 7.5 kA, second pulse welding time of 560 ms and first pulse holding time of 400 ms. It was also found that the ANN model predicted the tensile shear load with higher accuracy than the regression model.
