Showing 39 results for Treatment
M. Kazemi Pour, S. Sharafi,
Volume 5, Issue 1 (3-2008)
Abstract
Abstract: Hardfacing is one of the most useful and economical ways to increase the service life of
components subjected to abrasive wear. Iron based hardfacing alloys have long been considered
as candidate coatings for wear-resistant applications in industry. In the present work two layer of
Fe-34Cr-4.5C%wt hardfacing alloy was deposited on ASTM A36 carbon steel plates by SMAW
method. The microstructure consists of large primary and eutectic M7C3 carbides, metastable
austenite and small amount of secondary carbides. The microstructure was analyzed by optical
and scanning electron microscopes. In the same condition of size, shape, distribution and volume
fraction of carbides the as-welded matrix changed to martensite, tempered martensite and ferrite
by heat treatment processes. The wear resistance was measured by pin-on-disk method under loads
of 5, 10 and 20N and for sliding distance of 1500m. The results showed that the as-welded sample
with austenitic matrix has the most and the ferritic matrix specimen has the least wear resistance.
The predominate mechanisms for mass losses were determined to be micro-cutting, microploughing.
H. Shahmir, M. Nili Ahmadabadi, F. Naghdi,
Volume 5, Issue 4 (12-2008)
Abstract
Abstract: In the present study the effect of thermomechanical treatment (cold work and annealing) on the
transformation behavior of NiTi shape memory alloys was studied. Differential scanning calorimetry was used to
determine transformation temperature and its relation to precipitates and defects. Three alloys including Ti-50.3at.%
Ni, Ti-50.5at.% Ni (reclamated orthodontic wires) and 50.6at.% Ni alloy were annealed at 673 K and 773 K for 30
and 60 min after 15% cold rolling. It was found that the transformation characteristics of these alloys are sensitive to
annealing treatment and composition. The temperature range of transformation is broadened during cold working and
after subsequent annealing, the intermediate phase was appeared. The peaks become sharper and close together on
each cooling and heating cycle with increasing annealing temperature and time
M. Ebrahimi-Basabi,, J. Javadpour,, H. Rezaie, M. Goodarzi,
Volume 6, Issue 1 (3-2009)
Abstract
Abstract: Nano- size alumina particles have been synthesized by mechanical activation of a dry powder mixture of
AlCl3 and CaO. Mechanical milling of the above raw materials with the conditions adopted in this study resulted in
the formation of a mixture consisting of crystalline CaO and amorphous aluminum chlorides phases. There was no
sign of chemical reaction occurring during milling stage as evidenced by x-ray diffraction studies. Subsequent heat
treatment of the milled powder at 350ºC resulted in the occurrence of displacement reaction and the formation of
Al2O3 particles within a water soluble CaCl2 matrix. The effect of higher temperature calcinations on the phase
development in this powder mixture was followed by X-ray diffraction (XRD) analysis and scanning electron
microscope ( SEM). Differential thermal analysis (DTA) was used to compare the thermal behavior between the
milled and unmilled powders. Perhaps the most important result in this study was the observation of á-Al2O3 phase
at a very low temperature of 500ºC.
N. Anjabin, Karimi Taheri,
Volume 7, Issue 2 (6-2010)
Abstract
Abstract:
properties of AA6082 aluminum alloy. Considering that aging phenomenon affects the distribution of alloying element
in matrix, and the fact that different distribution of alloying elements has different impediments to dislocation
movement, a material model based on microstructure, has been developed in this research. A relative volume fraction
or mean radius of precipitations is introduced into the flow stress by using the appropriate relationships. The GA-based
optimization technique is used to evaluate the material constants within the equations from the uni-axial tensile test
data of AA6082 alloy. Finally, using the proposed model with optimized constants, the flow behavior of the alloy at
different conditions of heat treatment is predicted. The results predicted by the model showed a good agreement with
experimental data, indicating the capability of the model in prediction of the material flow behavior after different heat
treatment cycles. Also, the calculated flow stress was used for determination of the material property in Abaqus
Software to analyze the uniaxial compression test. The force- displacement curves of the analysis were compared to
the experimental data obtained in the same condition, and a good agreement was found between the two sets of results.
A novel constitutive equation has been proposed to predict the effect of aging treatment on mechanical
Y. Fouad,
Volume 7, Issue 4 (10-2010)
Abstract
Abstract: Rotating bending fatigue tests have been performed using smooth specimens of a rolled AZ31 magnesium alloy in laboratory air at ambient temperature. Fatigue strength and characteristic was evaluated and fracture mechanism was discussed on the basis fracture surface analysis. Electrical polishing (EP) as well as deep rolling (ball burnishing (BB)) U-notched specimens were performed on two groups of samples, to evaluate optimum conditions for fatigue life. The microstructure and tensile properties of roll cast (RC) Mg- 3% Al- 1% Zn (AZ31) was investigated. The fatigue strength of 107 cycles around 100 MPa for deep rolling while it was around 40 MPa for Electrical polishing. It was very important to understand the effect of (ball burnishing (BB)) conditions on the hardness of the surface through to the core. The two procedures improved the fatigue performance, but better improve in results were found in ball burnishing. The growth of small cracks initiated at the surface coincided with the FCP characteristic after allowing for crack closure for large cracks, but the operative fracture mechanisms were different between small and large cracks. At the subsurface crack initiation site, smooth facets were always present regardless of applied stress level.
S. H. Razavi, Sh. Mirdamadi, M. M. Hormozi,
Volume 8, Issue 1 (3-2011)
Abstract
Abstract: The aim of the present investigation is to study the physical and mechanical characteristics of dental-filling spherical high-copper and silver amalgams and to compare them with a common high-copper domestic unicompositional amalgam. In this study, cylindrical specimens were mechanically condensed according to the ISO 1559:1986 Standard in order to measure the compressive strength, Vickers hardness, static creep and dimensional change on setting. Adding more silver to the amalgam increased its compressive strength, creep resistance and reduced mercury vapor. After 1, 24 and 168h of amalgamation and Modulus of elasticity of specimen S1, the mean hardness and compressive fracture strength were significantly lower than those of . No significant differences were identified for the two alloys in the creep and dimensional changes on setting. It can be concluded that as far as the mechanical properties or corrosion resistance is concerned, the amalgam should be comprised of at least one spherical alloy.
A. Namiranian , M. Kalantar,
Volume 8, Issue 3 (9-2011)
Abstract
The process of mullitization of kyanite concentrate was studied at different conditions of heat treatment (1400
– 1600 °C and 0.5 – 3.5 hours) and particle size of raw materials (38-300 ?m). Kyanite concentrate was obtained from
ore-dressing of kyanite deposits of Mishidowan-Bafgh region at 100 km northeastern part of Yazd. The results of
microstructure (shape, distribution and size of the grains) and phase evolution studies by SEM and XRD showed that
total transformation of kyanite to mullite takes place by heat treatment between 1500 –1550 °C during 2.5 hours.. At
temperatures below 1500 °C need-like mullite grains are always produced. At higher temperatures the mullite grains
reveal rounded and platelet morphology. At 1550 °C, the rate of mullitization and densification were improved by
increasing soaking time from 1h to 3h and decreasing particle size of materials from 300 to 38 m
Dr Ali Darehkordi, Mr Mohammad Sadegh Hosseini,
Volume 9, Issue 3 (9-2012)
Abstract
Montmorillonite modified is an efficient environmental friendly catalyst under one-pot-three-component synthesis of 3,4-dihydropyrimidine-2(1H) ones. The preparation was performed with an aldehyde, 1,3-dicarbonyl compounds, urea or thiourea under solvent-free conditions. In comparison with the other methods of Biginelli reaction, this new method has short reaction time inexpensive catalyst and in addition excellent yields were obtained.
M. Alipour, S. Mirjavadi, M. K. Besharati Givi, H. Razmi, M. Emamy, J. Rassizadehghani,
Volume 9, Issue 4 (12-2012)
Abstract
In this study the effect of Al–5Ti–1B grain refiner on the structural characteristics and wear properties of Al–12Zn–3Mg–2.5Cu alloy was investigated. The optimum amount for Ti containing grain refiners was selected as 2 wt.%. T6 heat treatment, (i.e. heating at 460 °C for 1 h before water quenching to room temperature and then aging at 120 °C for 24 h) was applied for all specimens before wear testing. Dry sliding wear resistant of the alloy was performed under normal atmospheric conditions. The experimental results showed that the T6 heat treatment considerably improved the resistance of Al–12Zn–3Mg–2.5Cu alloy to dry sliding wear.
H. Arabi, S. Rastegari, V. Ramezani, Z. Valefi,
Volume 10, Issue 2 (6-2013)
Abstract
The objectives of this research were to find an economical way of reducing porosities in the microstructure of coatings deposited by flame spraying technique on CK45 steel and also trying to increase their cohesive strength to the substrate, so that the overall wear properties of this type of coating can be improved. So several specimens from this steel coated with NiCrBSi powder under specific conditions were subjected to various furnace heat treatment at 1000, 1025, 1050, 1075 and 1100 °C, each for periods of 5, 10 and 15 minute before cooling them in air. Tribological properties of treated coatings were evaluated by pin on disc method. The results show the highest wear resistance and microhardness values observed in one of the sample was due to lower amount of porosity and higher amount of very fine Cr2Ni3B6 particles precipitated homogeneously throughout its microstructure during specific heat treatment.
N. Khatami , Sh. Mirdamadi,
Volume 11, Issue 1 (3-2014)
Abstract
The presence of alloying elements, sometimes in a very small amount, affects mechanical properties one of these elements is Boron. In Aluminum industries, Boron master alloy is widely used as a grain refiner In this research, the production process of Aluminum –Boron master alloy was studied at first then, it was concurrently added to 2024 Aluminum alloy. After rolling and homogenizing the resulting alloy, the optimal temperature and time of aging were determined during the precipitation hardening heat treatment by controlled quenching (T6C). Then, in order to find the effect of controlled quenching, different cycles of heat treatment including precipitation heat treatment by controlled quenching (T6C) and conventional quenching (T6) were applied on the alloy at the aging temperature of 110°C. Mechanical properties of the resulting alloy were evaluated after aging at optimum temperature of 110°C by performing mechanical tests including hardness and tensile tests. The results of hardness test showed that applying the controlled quenching instead of conventional quenching in precipitation heat treatment caused reduction in the time of reaching the maximum hardness and also increase in hardness rate due to the generated thermo-elastic stresses rather than hydrostatic stresses and increased atomic diffusion coefficient as well. Tensile test results demonstrated that, due to the presence of boride particles in the microstructure of the present alloy, the ultimate tensile strength in the specimens containing Boron additive increased by 3.40% in comparison with the specimens without such an additive and elongation (percentage of relative length increase) which approximately increased by 38.80% due to the role of Boron in the increase of alloy ductility
K. Tavighi, M. Emamy, A. R. Emami,
Volume 11, Issue 4 (12-2014)
Abstract
This study was undertaken to investigate the effects of Cu and solution heat treatment on the microstructure and hardness of cast Al-Al4Sr metal matrix composite. Different amounts of Cu (0.3, 0.5, 1, 3 and 5 wt.%) were added to the composite. Specimens were heat treated at 500 °C for 4 hours followed by water quenching. Microstructural studies were assessed by the use of optical microscope, scanning electron microscope (SEM) and x-ray diffractometry (XRD). The results showed that addition of 5 wt.% Cu reduces the length of large needle-like Al4Sr phase and refines the microstructure. In addition, the presence of Cu-intermetallics increases hardness of the composite. Cu mainly forms θ phase which segregates at the grain boundaries. Heat treatment partially dissolves Cu-intermetallics and homogenizes the distribution of θ phase in the matrix.
S. Niksirat, Sh. Raygan, S. Moradi Ghiassabadi,
Volume 12, Issue 2 (6-2015)
Abstract
In this research, two different carbonaceous materials (Graphite:G and Petrocoke:P) were separately
compared in terms of the carbothermic reduction of hematite and anatase in order to synthesize Fe-TiC nanocrystalline composite by mechanically activated sintering method. Powders were activated in a planetary high-energy
ball mill under argon atmosphere for 0, 2, 5, 10,and 20 h. Then, the activated powders were analyzed by XRD and
SEM to investigate phase constituents and microstructure of the mixtures. Results proved that Fe
2
O
3
and TiO
2
were not
reduced by carbonaceous materials even after 20h of milling. SEM investigations showed that G-mixture was more
homogenous than P-mixture after 20h of milling, meaning that graphite-anatase-hematite was mixed satisfactorily.
Thermogravimetry analysis was done on 0 and 20h milled powders. TG and DTG curves showed that mechanical
activation led to almost 300°C decrease in the reduction temperature of hematite and anatase in both mixtures. In the
next step, the powders were sintered in a tube furnace under argon atmosphere. In the G-mixture, anatase was reduced
to titanium carbide at 1100°C but, in the P-mixture, temperature of 1200°C was essential for completely reducing
anatase to titanium carbide.Results of phase identification of the sintered powders showed that anano-crystalline ironbased composite with titanium carbide, as the reinforcement was successfully synthesized after 20 h high-energy
milling of the initial powders and subsequent sintering occurred at 1200˚C for 1h
M. Alipour, M. Emami, R. Eslami Farsania, M. H. Siadati, H. Khorsand,
Volume 12, Issue 4 (12-2015)
Abstract
A modified strain-induced melt activation (SIMA) process was applied and its effect on the structural characteristics and hardness of the aluminum alloy Al–12Zn–3Mg–2.5Cu was investigated. Specimens subjected to a deformation of 40% at 300 °C were heat treated at various times (10-40 min) and temperatures (550-600 °C). Microstructural studies were carried out using optical and scanning electron microscopies (SEM). Results showed that the best microstructure was obtained at the temperature and time of 575 °C and 20 min, respectively. The hardness test results revealed superior hardness in comparison with the samples prepared without the application of the modified SIMA process.
T6 heat treatment including quenching to 25 °C and aging at 120 °C for 24 h was employed to reach to the maximum strength. After the T6 heat treatment, the average tensile strength increased from 231 MPa to 487 and 215 MPa to 462 for samples before and after strain-induced melt activation process, respectively. Ultimate strength of globular microstructure specimens after SIMA process has a lower value than as-cast specimens without SIMA process
H. Torkamani, H. Rashvand, Sh. Raygan, J. Rassizadehghani, Y. Palizdar, C. Garcia Mateo, D. San Martin,
Volume 14, Issue 3 (9-2017)
Abstract
In industry, the cost of production is an important factor and it is preferred to use conventional and low cost procedures for producing the parts. Heat treatment cycles and alloying additions are the key factors affecting the microstructure and mechanical properties of the cast steels. In this study an attempt was made to evaluate the influence of minor Mo addition on the microstructure and mechanical properties of conventionally heat treated cast micro-alloyed steels. The results of Jominy and dilatometry tests and also microstructural examinations revealed that Mo could effectively increase the hardenability of the investigated steel and change the microstructure features of the air-cooled samples. Acicular microstructure was the consequence of increasing the hardenability in Mo-added steel. Besides, it was found that Mo could greatly affect the isothermal bainitic transformation and higher fraction of martensite after cooling (from isothermal temperature) was due to the Mo addition. The results of impact test indicated that the microstructure obtained in air-cooled Mo-added steel led to better impact toughness (28J) in comparison with the base steel (23J). Moreover, Mo-added steel possessed higher hardness (291HV), yield (524MPa) and tensile (1108MPa) strengths compared to the base one.
N. Nikoogoftar, S. H. Razavi, M. Ghanbari,
Volume 14, Issue 3 (9-2017)
Abstract
In this research, the effect of annealing and aging temperature as well as the effect of quenching media on the microstructure, hardness and dry sliding wear behavior of Ti-6Al-4V alloy has been studied. Cylindrical samples with the diameter of 10 mm and the height of 20mm were solutionized at 930˚C and 1060˚C for 600 seconds and then were quenched in the cold water and in the air. The samples were aged at different temperature of 480˚C, 550˚C and 610˚C for 360 s to increase the hardness. Heat treated samples were tested using standard pin-on-disc test machine at the applied loads of 100, 150 and 200 N. Microstructural investigations using scanning electron microscope revealed that for the samples solutionized at 930˚C and quenched in the water, the microstructure is composed of primary α and high volume fraction of martensitic α΄ phase with fine precipitated of β between martensitic lathes. In the case of air cooled samples, transformed β has also been appeared in the vicinity of primary α. For the samples solutionized at 1060˚C and quenched in the water, fully martensitic micro structure with fine β precipitates was observed. For the sample solutionized at 1060˚C and air quenched, plate like α and lamellar grain boundary β were detected. The maximum hardness value relates to the sample solutionized at 1060˚C and quenched in water which is equal to 433 HV. Different wear mechanisms, including oxidative wear, scratch, and delamination occurred at the worn surfaces at different applied loads. For the samples quenched in the water, the oxidative wear mechanism governing at low applied load and oxide debris was observed as separate or compacted particles which formed in the contact between pin and steel counter face detached from the sample. At higher applied loads, delamination and scratch mechanism was also observed and metallic plate like debris was detached from the sample. Mechanically mixed layer (MML) was formed on the surface of the pin at high applied loads and for the samples with low hardness value adhesion marks were also revealed on the steel disc. The minimum weight loss in the wear test is related to the sample quenched from the 1060ºC in the cold water and aged at 550 ºC .
M. Arockia Jaswin, D.m. Mohan Lal,
Volume 15, Issue 1 (3-2018)
Abstract
The behaviour of the cryogenically treated En52 martensitic valve steel has been experimentally analyzed in this paper. Material samples are subjected to deep cryogenic treatment after completing the regular heat treatment. The critical properties of the valve steel like wear resistance, hardness, tensile strength and impact strength are evaluated for the cryo treated En52 valve steel samples as per the ASTM standards. The microstructural changes and the mechanism behind the enhancement of the properties are examined and reported. The precipitation of fine carbides, transformation of retained austenite and refinement of carbides were the reasons behind the improvement of the mechanical properties. Deep cryogenic treatment process parameters are optimized for better wear resistance, hardness and tensile strength using grey Taguchi technique. Deep cryogenic treatment process greatly influences the wear resistance, a maximum enhancement of 54% is observed
M. Tavakoli Harandi, M. Askari-Paykani, H. Shahverdi, M. Nili Ahmadabadi,
Volume 16, Issue 1 (3-2019)
Abstract
One-step and two-step annealing techniques were used to examine the relationship between microstructure and mechanical properties during compression tests in iron-based ribbons and nanostructured 1- and 2.5mm cylindrical rods. The X-ray diffraction, microstructural, and mechanical results showed that substituting Nb for Fe had a minor effect on glass-forming ability but increased the formability index. The novel two-step annealing process resulted in a remarkable formability index of 16.62 GPa, yield stress of 2830 MPa, ultimate strength of 3866 MPa, and 4.3% plastic strain. A ductile nanosized α-Fe framework and boron-containing nano precipitations, which caused Zener pinning effect, were responsible for these novel mechanical properties.
M. Karimi Sahnesarayi, H. Sarpoolaky, S. Rastegari,
Volume 16, Issue 2 (6-2019)
Abstract
In this study nanosized TiO2coatings on the 316L stainless steel substrate were prepared by means of dip-coating technique in which thickness of the coating layer increased byrepeating the coating cycles in two different routes: (I) dipping and drying,respectively, were repeated one, three and five times and finally the dried coated sample was heat treated (single); (II) multiple heat treatment performed after each dipping and drying cycle, respectively.The structural, morphological and optical characterizations of coatings as well as thickness of coatings were systematically studied.The photocatalytic activity of the various TiO2 coatings was investigated based on the degradation of an aqueous solution of Methyl orange.Moreover, thecorrosion protective properties of coatings were evaluated in both dark and UV illumination conditions based on the obtained polarization curves. The results indicated 1.75 times improvement in photocatalytic reaction rate constant, a two orders of magnitude decrease in corrosion current density in dark condition and about 140 mV electrode potential reduction under UV illumination with optimum coating preparation procedure, repeating the cycle from dipping to heat treatment three times, than the sample prepared with one time coating and heat treatment since this procedure provided not only high thickness and defect-free coating but also transparent one.
A. Khalili, M. Mojtahedi, M. Goodarzi, M. J. Torkamani,
Volume 16, Issue 3 (9-2019)
Abstract
The aim of this work was to synthesize TiC reinforced coating on carbon steel via reduction of ilmenite powder. A mixture of ilmenite and graphite was pre-placed on AISI 1020 steel surface. The effect of the addition of excess graphite amounts on the progress of synthesis of carbide particles was studied. The evolution of phases in different coatings was analysed via X-ray diffraction and scanning electron microscopy. Then again, the initial powder mixtures were mechanically activated for various durations, to accelerate the reactions in transient melt pool. Finally, the Fe-TiC hard coating was successfully synthesized by carbothermic reduction of ilmenite through laser surface treatment. Moreover, it is proved that combination of mechanical activation with additive laser melting effectively improves the level of ilmenite reduction, besides enhancing the distribution of hard particles and the hardness of the coatings to more than 1300 HV.
